MSG6130F Intelligent Differential Pressure Transmitter

Product Features	benefitUsing MSG6130 intelligent differential pressure transmitter, equipped with welded sealed oil filled isolation diaphragm structure, adopting flat flange and extension
	Flat flange, capillary remote transmission clamp flange, sanitary lock nut pressure rotary multiple connection methods, widely applicable to high temperature and corrosion
	Differential pressure and liquid level measurement under clean conditions!

working principle	The medium pressure acts on the metal isolation corrugated membrane and is transmitted to the sensitive element beta chamber for measurement through the intermediate silicone oil
	The diaphragm senses differential pressure to form a capacitance change, and the differential pressure forms a linear state with the differential capacitance to detect electricity
	The differential pressure capacitance is amplified and converted into a standard current signal for output.

---

---

Technical Specifications	·Measurement range	Minimum measurement range 0~500Pa, maximum measurement range 0~4MPa
	·Accuracy	The comprehensive error (including linearity, repeatability, and hysteresis) is better than 0.1%
		<7KPa: 0.25% rated range 1:1~3:1 (0.25% standard range+0.03% TD)%
		Set the range to 3:1 to 10:1
		≥ 7kPa: 0.2% standard range 1:1~3:1 (0.2% standard range+0.03% TD)%
		Set the range to 3:1 to 10:1
	·Long term stability	Annually ≤ ± 0.15% Fs
	·Working temperature	Allowable medium temperature (-40~100) ℃, allowable storage temperature (-40~85) ℃
		Allowable ambient temperature (-20~60) ℃ (special requirement -40~85 ℃)
	·Temperature influence	-Within the temperature range of 20 ℃ to+60 ℃, the influence error (zero point, range) is ≤ 0.8%
		The influence error of the 7KPa range sensor is ≤ 1.2%
	·Temperature coefficient	-10 ℃~+60 ℃ (0.05% URL+0.065% set range)/20K
		-40 ℃~-10 ℃ 60 ℃~+85 ℃ (0.08% URL+0.1% set range)/20K
	·Long term stability and qualitative analysis	Better than 0.1% FS per year and better than 0.25% for five years
	·Sensors allow Working static pressure	Unidirectional and bidirectional maximum allowable static pressure PN13MPa
	·Static pressure influence	Under 100% condition, the impact is ≤ 0.25%
	·Damping	0-40 seconds continuously adjustable
	·Allow environmental humidity	100%HR
	·Signal output	4-20mA linear output two-wire system with HART communication protocol
		4-20mA square root output two-wire system with HART communication protocol
	·Start time	3S without preheating required
	·Vibration impact	2g 1000HZ ±0.05%
	·Impact resistance	50g 11mesc
	·Load characteristics	Corresponding to power supply voltage impedance of 50 Ω~1000 Ω (see figure)
	·Power supply	12V～36V DC
	·Sensor range ratio	20: 1. Continuously adjustable, zero point can be reversed and migrated 100%
	·Installation location impact	Non horizontal installation generates a zero point error of less than 0.25KPa, which can be corrected by adjusting the zero point,
		Does not affect measurement accuracy
	·Electrical connection	The cable sealing shell is suitable for cables with an outer diameter of 6-8mm;
	·Process Connection	1/4NPT internal thread; Connection of pressure conduit; M10 internal hole thread; Installation bracket connection
	·Contact with medium	Sensor corrugated membrane: stainless steel 316L, Hastelloy C;
	Partial materials	Sensor sealing ring: Fluorine rubber EPDM, PTFE carat (Kalrez);
		Flange: Stainless steel 316, Hastelloy C
	·Non contact with the medium	Shell: Die cast aluminum strip with epoxy resin coating; Fastener: Stainless steel
	Partial materials	Nameplate: Stainless steel 304; Intermediate fluid in sensor: silicone oil
	·On site terminal	Intelligent: 5-digit LCD digital display; Simulation: 3 1/2 digit LCD digital display
	·Explosion proof level	Explosion proof Ex d Ⅱ C T6 Gb; Intrinsically safe Ex ia Ⅱ C T6 Ga

---

---

external structure

electrical connection

M5 terminal screw suitable for 0.5-1.5m ㎡ wire diameter

M20 × 1.5 internal thread cable entry hole, with cable sleeve for cables with outer diameter of 6-8mm ²

Instrument installation

Process Connection (1)

[-] Compression end elliptical flange internal thread connection thread standard: process screw hole 1/4-18NPT/installation screw hole M10 [see above figure]

[+] Flat flange or extended flange welding sealing diaphragm structure connection: Flange standard: GB9123-88 DN50、DN80、DN100、PN4MPa，

Extension flat flange: GB9123-88 DN80, PN4MPa, extension 50mm, 10mm, 200mm [see above figure]

Process Connection (2)

a、 Capillary lock nut pressure rotary welding sealing diaphragm structure
Connection standard: DIN11851-DN50, DN65, DN80, DN100PN 2.5MPa [see above figure]

b、 Capillary clamp flange welding sealing diaphragm structure
Flange standards: GB9123-88 DN50, DN80, PN1.6MPa/40MPa [see above figure]

Order Selection Table