- Phone
-
Address
Building 11, Hengfeng Petrochemical, Block B, Ganlu Industrial Park, Ehu Town, Xishan District, Wuxi City
Product Categories
Wuxi Jiuying Environmental Testing Equipment Co., Ltd
Walk in dustproof test chamber
NegotiableUpdate on 05/07
- Model
- Nature of the Manufacturer
- Producers
- Product Category
- Place of Origin
Overview
The main function of the walk-in dustproof test box is to test the physical and other related properties of electronic and electrical products, lamps, electrical cabinets, electrical components, automobiles, motorcycles and their parts under simulated dust climate conditions. After testing, the performance of the product is evaluated through calibration to determine whether it meets the requirements, in order to facilitate the design, improvement, calibration, and factory inspection of the product.
Product Details
1Walk in dustproof test chamber--Technical parameters:
| model | Studio size (mm) | Dimensions (D * W * H) mm |
| SC-512 | 800×800×800 | 1270×970×1800 |
| SC-800 | 800×1000×1000 | 1270×1220×2050 |
| SC-1000 | 1000×1000×1000 | 1500×1200×2050 |
| SC-1500 | 1000×1500×1000 | 1500×1700×2050 |
IITechnical specifications of walk-in dust-proof test chamber：
1. Metal mesh wire diameter: 50um
2. Nominal spacing between: 75um
4. Resistance time: 0-99H59M
5. Fan cycle time: 0-99H59M
6. Temperature range RT+5 ℃~+40 ℃; (If the test time is too long, the temperature will rise)
7. The dust specification can pass through a square hole with a mesh size of 75um and a metal diameter of 50um
9. Sample rack load ≤ 30kg
10. Experimental dust silicate cement, flue ash, etc
11. Vibration mode intermittent, continuous (adjustable)
12. Intermittent and continuous (adjustable) dust blowing method
13. Power supply AC380V ± 10% 50Hz/AC220V ± 10% 50Hz;
14. Time control is continuously adjustable from 1 to 9999 (S, M, H), with a period of 99 to 99 (S, M, H)
IIIWalk in dustproof test chamberMaintenance and Care
1. If you hear any abnormal noise during operation, please stop the machine for inspection and wait for the fault to be found and resolved before restarting to avoid affecting the service life of the equipment.
2. Keep the appearance of the box clean;
3. Avoid external impact on the box body; When moving devices, avoid dropping, colliding, scratching, twisting, striking, vibrating, or squeezing the equipment;
4. Avoid tilting the equipment;
5. Chemical contact with this equipment is prohibited;
6. Keep the laboratory in a dry environment;
7. Check the circuit control system before each startup;
8. Confirmation of power supply and grounding wire;
9. Whether the power cord is properly connected according to specifications and grounded properly;
10. Ventilation fans should be installed in the laboratory to maintain indoor ventilation;
After the experiment is completed, cut off the power supply of the whole machine;
After each experiment, the sample should be taken out and the inner container of the equipment should be cleaned thoroughly;
13. Non professionals are strictly prohibited from operating this equipment.
4Walk in dustproof test chamberRequirements for installation site
1. Avoid environments with high humidity, direct sunlight, and dust.
2. A space of 80 centimeters should be left around, and it should not be tightly attached to walls or other testing equipment.
3. For the stability of the sand and dust test chamber, the ambient temperature and humidity should be maintained at a temperature of 5 ℃ to 30 ℃ and a humidity of ≤ 85% R.H.
4. To avoid uneven unevenness, it should be installed on a horizontal ground.
5. The installation site should have good ventilation and be easy to operate around.
