Optris flame infrared thermometer CTlaser MT

NegotiableUpdate on 01/03

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

The Optris flame infrared thermometer CTlaser MT from Optris has a special measurement wavelength and can measure temperatures through 200 ° C; C to 1650 Accurate temperature measurement of C flame. Therefore, it is suitable for monitoring workpieces in ovens, measuring in chemical reactors, and testing refractory linings in kilns. The $r $n stainless steel probe adopts dual laser goggles, which can mark measurement points at any distance at any time. Even small objects with a size of only 1.6mm can easily measure their temperature with an infrared thermometer.

Product Details

Optris flame infrared thermometer CTlaser MTWith a special measurement wavelength, accurate temperature measurement is carried out through flames ranging from 200 ° C to 1650 ° C. Therefore, it is suitable for monitoring workpieces in ovens, measuring in chemical reactors, and testing refractory linings in kilns.

The stainless steel measuring head adopts dual laser goggles, which can mark measurement points at any distance at any time. Even small objects with a size of only 1.6mm can easily measure their temperature with an infrared thermometer.

Optris flame infrared thermometer CTlaser MT

Product Specifications

measurement parameters
Temperature range (measured through setting keys or software)	200°C ~ 1450°C
spectral range	3.9 µm
Optical resolution (90% energy)	45:1
Optional Focus	CF1 1.6 mm @70 mm CF2 3.4 mm @ 150 mm CF3 4.5 mm @ 200 mm CF4 10 mm @ 450 mm SF 27 mm @ 1200 mm
System accuracy (Note 1) (Environmental temperature=23 ± 5 ° C)	± 1% (Note 2)

Repetitive accuracy (ambient temperature=23 ± 5 ° C)	± 0.5% or ± 0.5 ° C (Note 2)
Temperature resolution (digital)	0.1°C
Response time (90% signal) (Note 3)	10 ms
Emissivity/gain (adjusted by setting keys or software)	0.100 ~ 1.100
Transmittance/gain (adjusted by setting keys or software)	0.100 ~ 1.100
Signal processing (specific parameters can be adjusted through setting keys or software)	Peak hold, valley hold, average, extended hold threshold, and lag function
Basic Parameters
environmental level	IP65（NEMA-4）
ambient temperature	Probe: -20 ° C~85 ° C (laser on at 50 ° C); Electronic box: 0 ° C~85 ° C
Storage temperature	Probe: -40 ° C~85 ° C; Electronic box: -40 ° C~85 ° C
relative humidity	10~95%, no condensation
Vibration (sensor)	-IEC 60068-2-6 (sinusoidal waveform)/- IEC 60068-2-64 (wideband noise)
Impact (sensor)	-IEC 60068-2-27 (25G and 50G)
weight	Probe: 600 g; Electronic box: 420 g
Electrical parameters
analog output	Channel 1: 0/4-20mA, 0-5/10V, thermocouple J, K Channel 2: Probe temperature (0-5 V or 0-10 V corresponds to -20-85 ° C), alarm output
alarm output	0-24V/50 mA (normally open)
optional	Relay: 2 x 60 V DC/42 V AC; 0.4 A; optical isolation
Digital output (optional)	USB, RS232, RS485, Modbus RTU (serial communication protocol), Profibus DP (fieldbus multifunctional slave design), Ethernet
Output impedance	MA Max 500 Ω (DC 5-36 V); MV Min 100 k Ω (pure impedance load); Thermocouple 20 Ω
signal input	Programmable function input, used for external emissivity adjustment/environmental temperature compensation, triggering (holding function reset)
cable length	3m (standard), 8m, 15m
power supply	DC 8-36 V
Current consumption	Max 160 mA
Laser 635 nm	1mW， Open/close through electronic box or software
Note 1	ε (emissivity)=1, response time: 1s
Note 2	The temperature of the object is higher than 300 ° C
Note 3	Dynamic adaptation at low signal levels

OPTLaserMT flame specific series infrared thermometer

model	temperature range	temperature measurement accuracy	response time	distance coefficient	spectral response
Optctlmt	200～1450℃	±1%	10ms	45：1	3.9μm
Optctlmth	400～1650℃	±1%	10ms	45：1	8～14μm
Measure the spot and focal length	CF1： 1.6mm@70mm ；CF2 3.4mm@150mm ；CF3： 4.5mm@200mm CF4： 10mm@450mm ；SF： 27mm@1200mm
Operating Temperature	Probe: -20~85 ℃, electronic box: 0~85 ℃
analog output	0/4-20mA, 0-5/10V, J/K type thermocouple signal output
digital output	USB、RS232，RS485，CAN-Bus,Profibus DP, Ethernet 可选
emissivity	0.100~1.100 software settings
Connecting cable length	3m, 8m, 15m optional
signal processing	Peak holding, valley holding, average value.
power supply	8～36VDC
application	Measuring workpiece temperature through flame: measurement of heat treatment temperature and heating furnace temperature