MFP 3000 M filter test bench

NegotiableUpdate on 01/21

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

The aerosol inlet on the MFP 3000 M filter test bench is designed for 1000 mg/m; The high-quality concentration is specially customized and can ensure the uniform distribution of test aerosols in the raw gas channel. Due to its simple structure, the raw material gas channel can be easily cleaned.

Product Details

MFP 3000 M filter test benchThe version is specially customized according to the requirements of ISO 5011 and the measurement procedure of ISO TS 19713-2:

Generate aerosols using RBG 1000 G:

The metering air of the RBG 1000 G solid particle aerosol generator is regulated by a mass flow controller. This will ensure that specific operating conditions are always maintained.
Additional solid material storage tanks and dispersion covers can provide optimal metering time at different air volume flow rates.

DLB 2000 compressed air humidifier for dispersing air:

Dry compressed air is commonly used to generate aerosols, and when the volumetric flow rate in filter material testing is very low, the relative humidity of the tested volumetric flow rate may significantly decrease. The DLB 2000 compressed air humidifier can accurately adjust the relative humidity and temperature of RBG 1000 dispersed air to the desired values, thereby minimizing the impact of relative humidity on the testing ash storage capacity.

Aerosol inlet on MFP 3000 M:

The aerosol inlet on the MFP 3000 M is specially customized for high-quality concentrations of 1000 mg/m ³ and ensures uniform distribution of test aerosols in the raw gas channel. Due to its simple structure, the raw material gas channel can be easily cleaned.

welas ® 2070 aerosol sensor:

welas ® The 2070 high concentration sensor ensures clear and reliable classification and separation efficiency testing at high concentrations up to 1000 mg/m3. These sensors are also equipped with special aerosol conduits to minimize contamination of internal optical components.

Software:

Various pressure differential levels can be set for feeding according to ISO 5011 in the filter material testing sequence program. Clearly defining test parameters in pre programmed sequence programs ensures a high level of comparability of results.

MFP 3000 M filter test benchAdvantages:

Almost simultaneously measure particles in raw materials and clean gases
The particle size measurement range is 0.2-40 µ m
Can measure Cn max=106 particles/cm3 without dilution
• Comparable measurement results on an international scale
Widely distributed measurement systems
High reproducibility of testing methods
• Easy to use different test aerosols, such as SAE coarse powder NaCl/KCl、DEHS
In the feeding test, the highest concentration of raw material gas can reach>1000 mg/m3 (ISO fine particles) or>5000 mg/m3 (ISO coarse particles) when measuring the classification separation efficiency
Flexible filter testing software FTControl
• Sequential program for pressure loss measurement, graded separation efficiency measurement, and loading measurement
• Easy to operate, even untrained personnel can quickly use the device
• Short setup time
• Customers can independently perform cleaning and calibration
• Easy use of measurement technology components - even in other applications
• Mobile settings, use casters to move
• Reliable operation
Verify the functionality of individual components and the entire system during pre delivery acceptance testing and upon delivery
• Low maintenance
The device will reduce your operating costs

Application:

Test filter media and small filter components during product development and production monitoring.
• Testing based on ISO 5011 for engine intake filters

Parameters:

Measurement range (size)	0.2 – 40 µm
volumetric flow rate	1-35 m3/h (suction mode)
Overall dimensions	680 • 2500 • 1550 millimeters (width • height • depth)
Inflow velocity	5-100 cm/s (other specifications can be provided upon request)
Differential pressure measurement	0 – 5,000 Pa
Filter material testing area	100 cm²
aerosol	Dust (such as SAE dust), salt (such as NaCl, KCl), liquid aerosol (such as DEHS)
Aerosol concentration	For SAE fine dust, it can reach up to 1000 mg/m3 (ISO A2 fine dust) without additional dilution
Compressed air supply	6–8bar