Intelligent wireless THUM adapter

Most factories have hundreds or even thousands of HART instruments, all equipped with rich diagnostic and process information, which is often unused

You cannot improve the areas that cannot be seen

Most factories have hundreds or even thousands of HART instruments, all with rich diagnostic and process information, which is often not used because it is difficult to access or too costly through traditional wired channels. today we are no longer as we have been. ..

Unleash the value of existing on-site equipment

The intelligent wireless THUM adapter is a device that can be retrofitted on any existing two-wire or four wire HART device, and it can wirelessly transmit measurement and diagnostic information that could not be transmitted before. This is a simple method to access the existing on-site intelligence in the factory. The main advantages include:

Extend predictive intelligence to previous technological advancements

Areas that cannot be used due to economic reasons

Enable any HART device to have wireless functionality to obtain new measurement points

Use advanced instrument diagnostic functions

Remote management of devices and monitoring of device operation status

Efficiently collect data from multivariate devices

Provide enhanced valve capabilities

The built-in solution can provide rich wireless HART ™ data

2-wire or 4-wire HART devices

No special power requirements

Intelligent power circuit acquisition

Battery-free

Flexibly meet the most demanding application requirements

Wireless outputs with data reliability of over 99% can provide rich HART data and are protected by industry-leading security measures

Obtain more HART information, such as diagnostic or multivariate data

Add wireless functionality to almost any measurement point

The Wireless HART feature integrates PlantWeb ® Extend all advantages to previously unreachable locations

Functional specifications

Input: Any 2-wire or 4-wire HART powered device.

Output: Wireless HART

Humidity limit: 0-100% relative humidity

Refresh rate: User selectable, 8 seconds to 60 minutes

Physical specifications

Electrical connection:

The THUM adapter is connected to a 4-20mA power supply circuit, which collects electrical energy to power itself without affecting the 4-20mA signal in the circuit. Linear voltage drop: 2.25 volts at 3.5 mA to 1.2 volts at 25 mA. In the fault state, the maximum voltage drop is 2.5 volts.

Power Supply:

The minimum load of 250 ohms in the circuit can maintain the normal operation function of the sub device, and the power in the circuit must have at least 2.5 V margin under a 250 ohm load.

HART controller connection:

Connect via wired device HART

structural material

Shell:

Shell - Low Copper Aluminum

Paint - Polyurethane

Antenna:

Polybutylene terephthalate (PBT)/polycarbonate (PC) combination

Omnidirectional antenna

Weight:

0.65 lbs. (0.29 kg)

Shell grade

The housing option code D is NEMA 4X and IP66.

Installation method:

The THUM adapter can be directly connected to the conduit of a 2-wire or 4-wire HART 5.0 device.

Performance Specifications

Electromagnetic Compatibility (EMC)

All models:

When installing with shielded wires, all relevant requirements of EN 61326-1 (2006) must be met. Sub devices must also be installed using shielded wires.

Vibration impact:

When tested on site according to the requirements of IEC60770-1 using ordinary applications or low vibration level pipelines (10-60 Hz 0.15 mm displacement peak amplitude/60-500 Hz 2g), the output is not affected. When using a THUM adapter on wired devices with vibration levels greater than 2g, it is recommended to install the THUM adapter remotely.

Temperature limit:

Operating limit: -40 to 185 ° F (-40 to 85 ° C)

Storage limit: -40 to 185 ° F (-40 to 85 ° C)

Output specifications:

The THUM adapter allows for wireless HART communication between the connected HART device and the smart wireless gateway ™ Communicate

Use advanced instrument diagnostic functions

Rosemount 3051S with Advanced Process Diagnostics

High precision Coriolis instrument calibration with optional AMS instrument calibration SNAP-ON option

Rosemount radar echo curve

Rosemount electromagnetic flowmeter instrument calibration with AMS device management system

Efficiently collect data from multivariate devices

Rosemount 3051SMV MultiVariable ™ And 3095 mass flow transmitter

Rosemount 3300 and 5300 radar level transmitters

High-precision Coriolis instrument

Rosemount TankRadar Rex and TankRadar Pro level gauges

Rosemount electromagnetic flowmeter

Rosemount Multivariable ™ vortex flow meter

Enable any HART device to have wireless functionality to obtain new measurement points

liquid level

traffic

valve

Liquid and gas analysis

pressure

temperature

Using AMS device management system to remotely manage devices and monitor their operational status

Reduce troubleshooting time

Record pre - and post event data

Calibration tracking

Provide enhanced valve capabilities

Online testing of valves in use using AMS ValveLink SNAP-ON

Using AMS equipment management system to monitor travel deviation, gas source pressure, and electronic component operation status alarms

Provide trends of actual valve positions