German House Parker Honsberg piston flow switch flowmeter

German House Parker Honsberg piston flow switch flowmeter

German House Parker Honsberg piston flow switch flowmeter

flow switch
Indicator option: without mechanical indicator
Nominal diameter: DN 10-G ⅜
Connection method: Internal thread
Connection material: Nickel plated brass
Voltage resistance: PN 200
Sealing element: Nitrile rubber
Medium temperature: -20 .. +120 °C
Environmental temperature: -20 .. +70 °C
Adjust H ₂ O: 2 l/min H ₂ O
Switch head: plastic flat head
Adjustment: Long hole
Electrical connection: plug DIN 43650-A/ISO 4400
Electrical contact: Reed switch
maximum. Contact load: 120 V AC 0,18 A 5 VA/175 V DC 0,25 A 5 W
Wiring diagram: conversion, diode, wiring diagram number. zero point three four seven
Protection type: IP65
Flow direction: Vertical from below
Signal light: red/green plug DIN 43650-A
Country of Origin: Germany

Flow switch MR1K-
● High switching power
● Compact design
feature
Mechanical flow switch, used for fluid or gas media, with
Spring supported piston and magnetic trigger of magnetic spring switch.
Sturdy brass or stainless steel structure.
Technical data
Switch reed switch
Nominal width DN 8.25
process
contact
Internal thread G 1/4. G 1
More process connections can be found at
Requirement)
Switch range 0.4.. 60 l/min
For details, see
The pressure loss at Qmax is 0.4... 1.4 bar. Table 'Scope'
Qmax。 Up to 80 liters per minute
Tolerance ± 5% of full-scale value
pressure
resistance
PN 200 bar optional PN 500 bar
Medium temperature -20..+120 ℃ optional -20..+150 ℃
surroundings
temperature
-20..+70 °C
Medium water (oil, gas, and corrosive medium)
The requirement can be fulfilled
Wiring conversion
no zero point two one three
optional
transformation
no zero point two eight two
Optional red or red/green diodes
DIN 43650-A plug
Maximum switch voltage 175 volts DC/120 volts AC
Maximum switch current 0.25 A DC/0.18 A AC
exchange
capacity
maximum. 5 watts per volt ampere
Protection Level 2- Safety Insulation
Protection level IP 65
electrical
contact
Plug DIN 43650-A/ISO 4400, optional
Circular plug connector M12x1, 4-pin
material
Media exposure
Brass structure:
CW614N nickel plating,
CW614N，1.4310，
Hard ferrite, NBR
stainless steel
Structure: 1.4571,
1.4404, 1.4310, hard
Ferrite PTFE coating,
FKM
Non moderate contact
material
PA、CW614N、 Nitrile rubber
Please refer to the table "Dimensions and Weight" for the weight
install
location
Standard: Horizontal inward flow
be left over; Other installation locations are also possible;
Installation location affects switching
Point and Range.
scope
For the switch range, the detailed information in the table corresponds to
Horizontal inward flow and reduced flow velocity; Used for displaying range
They correspond to horizontal inward flow and increased flow
Speed.
exchange
scope
display range
Liters per minute of H2O
Qmax 。
Highly respected
pressure loss
At Qmax's bar. water
Liter/minute H2O O/O1 J
0.4 - 4 0.5 - 5 0.4 - 4 10 0.6
1.0 - 10 1.0 - 12 1.0 - 10 20
2.0 - 20 2.0 - 23 2.0 - 20 30 0.4
3.0 - 30 3.0 - 34 3.0 - 30 40
4.0 - 40 4.0 - 45 4.0 - 40 60 0.8
6.0 - 60 6.0 - 65 6.0 - 60 80 1.4
Special ranges can be provided.
Dimensions and Weight
Weight of G-type SW X
kilogram
Brass G 1/4 MR1K-008GM 40 15 1.3
G 3/8 MR1K-010GM
G 1/2 MR1K-015GM
G 3/4 MR1K-020GM 18 1.2
G 1 MR1K-025GM 1.1
rust-proof
steel
G 1/4 MR1K-008GK 41 15 1.2
G 3/8 MR1K-010GK
G 1/2 MR1K-015GK
G 3/4 MR1K-020GK 18 1.1