Full diameter rock vacuum saturation device

Full diameter rock vacuum saturation device

The vacuum saturation system should at least include: vacuum equipment, airtight vacuum tank, liquid storage and immersion tankPump equipment, convenient control cabinet, other accessories such as gas-liquid pipes, control valves, vacuum gauges, etc.

Vacuum pumping equipment:Purchase standard vacuum pumps and select the appropriate power vacuum pump based on the total volume of the vacuum deviceSimultaneously evacuate four vacuum tanks and maintain the vacuum for at least 5 hours, with a requirement for a minimum vacuum levelAt -0.0986Mpa (29 inches of mercury).Figure 2 Schematic diagram of vacuum saturation tank2）Airtight vacuum tankAn airtight vacuum tank is required, with at least one side capable of observing the sandstone target inside the tube, and organic materials can be usedMade of glass, convenient for observing the rise of liquid level when saturated, with the vacuum tank suction port above,There is an inlet and outlet below, and the inlet and outlet should have a buffer filtration device to ensure that the liquid enters from the bottom of the target bodyFilter sand and impurities while entering and exiting the liquid; To increase the efficiency of vacuum extraction, at leastFour vacuum tanks work together, with each tank requiring an inner diameter of no less than 250mm and a height of no less than1000mm. Vacuum tank with vacuum gauge required.Figure 3 Schematic diagram of vacuum saturation tank3）Pump equipmentSalt water needs to be extracted from the storage tank and supplied to the vacuum tank. After saturation is complete, the inside of the vacuum tank should be emptiedExtract the liquid into the storage tank. The pumping equipment should be equipped with adjustable flow control valves to control the inflowLiquid velocity, to avoid the liquid level rising too quickly.4）Liquid storage tankUsed for configuring saturated liquids, storing saturated liquids, and soaking sandstone. The liquid storage device should be equipped with separate componentsZone, solution preparation zone, saturated sandstone target immersion zone (with at least 15 sandstone targets placed).The solution preparation area needs to be connected to the channel for pumping liquid into the vacuum tank and the cleaning and drainage channelInstall a filtering device to prevent impurities and sand from blocking the pipeline. The sandstone target immersion area should be easy to liftTake sandstone targets and ensure that the targets are isolated from each other to avoid collision.5）Convenient control cabinetNeed to control and set parameters for vacuum pumps and pump liquid equipment, with control switches and parametersThe numerical settings include vacuum value, holding time after vacuuming, timed shutdown, and vacuum compensationThe pump switches and inlet flow control valves of each pipeline are used for flow control.6）Other fixturesConvenient transportation gripper for target body (ensuring easy lifting and transportation of sandstone targets without damaging sandstone targets), electricSub scale (used for weighing dry and wet weight of sandstone targets, requiring a range of 200kg and an accuracy of 1g)Safety and environmental protection requirements1）Electrical equipment should be grounded to prevent static electricity accumulation;2）The equipment configuration should fully ensure reliability and maturity, with a reasonable layout and simple operation and maintenanceConvenient, ensuring safe and reliable operation;3）Liquid collection trays should be considered at the saturation device and pump to prevent the leakage of saturated liquid and pollution of the environment;4）Due to the medium being saltwater, corrosion-resistant materials should be considered for material selection.

1. Inner diameter of organic saturation cylinder: φ 250x1000mm4set

2.Vacuum pump 20m ³/h1platform

3.vacuum gauge-0.098MPa4only

4.High pressure valve DW612Only

5.High pressure shut-off valve DW65only

6.Pipeline process DW6/20MPa1Set up

7.Stainless steel inlet pump 10L/h1Taiwan Shanghai

8.Vacuum storage tank 2L1platform

9.Electric control 220V1set

10.Mobile bracket aluminum profile1set

11.Filter DW64a

12.Stainless steel core basket, diameter 200x1000mm4A

Full diameter rock vacuum saturation device

The vacuum saturation system should at least include: vacuum equipment, airtight vacuum tank, liquid storage and immersion tankPump equipment, convenient control cabinet, other accessories such as gas-liquid pipes, control valves, vacuum gauges, etc.

Vacuum pumping equipment:Purchase standard vacuum pumps and select the appropriate power vacuum pump based on the total volume of the vacuum deviceSimultaneously evacuate four vacuum tanks and maintain the vacuum for at least 5 hours, with a requirement for a minimum vacuum levelAt -0.0986Mpa (29 inches of mercury).Figure 2 Schematic diagram of vacuum saturation tank2）Airtight vacuum tankAn airtight vacuum tank is required, with at least one side capable of observing the sandstone target inside the tube, and organic materials can be usedMade of glass, convenient for observing the rise of liquid level when saturated, with the vacuum tank suction port above,There is an inlet and outlet below, and the inlet and outlet should have a buffer filtration device to ensure that the liquid enters from the bottom of the target bodyFilter sand and impurities while entering and exiting the liquid; To increase the efficiency of vacuum extraction, at leastFour vacuum tanks work together, with each tank requiring an inner diameter of no less than 250mm and a height of no less than1000mm. Vacuum tank with vacuum gauge required.Figure 3 Schematic diagram of vacuum saturation tank3）Pump equipmentSalt water needs to be extracted from the storage tank and supplied to the vacuum tank. After saturation is complete, the inside of the vacuum tank should be emptiedExtract the liquid into the storage tank. The pumping equipment should be equipped with adjustable flow control valves to control the inflowLiquid velocity, to avoid the liquid level rising too quickly.4）Liquid storage tankUsed for configuring saturated liquids, storing saturated liquids, and soaking sandstone. The liquid storage device should be equipped with separate componentsZone, solution preparation zone, saturated sandstone target immersion zone (with at least 15 sandstone targets placed).The solution preparation area needs to be connected to the channel for pumping liquid into the vacuum tank and the cleaning and drainage channelInstall a filtering device to prevent impurities and sand from blocking the pipeline. The sandstone target immersion area should be easy to liftTake sandstone targets and ensure that the targets are isolated from each other to avoid collision.5）Convenient control cabinetNeed to control and set parameters for vacuum pumps and pump liquid equipment, with control switches and parametersThe numerical settings include vacuum value, holding time after vacuuming, timed shutdown, and vacuum compensationThe pump switches and inlet flow control valves of each pipeline are used for flow control.6）Other fixturesConvenient transportation gripper for target body (ensuring easy lifting and transportation of sandstone targets without damaging sandstone targets), electricSub scale (used for weighing dry and wet weight of sandstone targets, requiring a range of 200kg and an accuracy of 1g)Safety and environmental protection requirements1）Electrical equipment should be grounded to prevent static electricity accumulation;2）The equipment configuration should fully ensure reliability and maturity, with a reasonable layout and simple operation and maintenanceConvenient, ensuring safe and reliable operation;3）Liquid collection trays should be considered at the saturation device and pump to prevent the leakage of saturated liquid and pollution of the environment;4）Due to the medium being saltwater, corrosion-resistant materials should be considered for material selection.

1. Inner diameter of organic saturation cylinder: φ 250x1000mm4set

2.Vacuum pump 20m ³/h1platform

3.vacuum gauge-0.098MPa4only

4.High pressure valve DW612Only

5.High pressure shut-off valve DW65only

6.Pipeline process DW6/20MPa1Set up

7.Stainless steel inlet pump 10L/h1Taiwan Shanghai

8.Vacuum storage tank 2L1platform

9.Electric control 220V1set

10.Mobile bracket aluminum profile1set

11.Filter DW64a

12.Stainless steel core basket, diameter 200x1000mm4A

Full diameter rock vacuum saturation device

The vacuum saturation system should at least include: vacuum equipment, airtight vacuum tank, liquid storage and immersion tankPump equipment, convenient control cabinet, other accessories such as gas-liquid pipes, control valves, vacuum gauges, etc.

Vacuum pumping equipment:Purchase standard vacuum pumps and select the appropriate power vacuum pump based on the total volume of the vacuum deviceSimultaneously evacuate four vacuum tanks and maintain the vacuum for at least 5 hours, with a requirement for a minimum vacuum levelAt -0.0986Mpa (29 inches of mercury).Figure 2 Schematic diagram of vacuum saturation tank2）Airtight vacuum tankAn airtight vacuum tank is required, with at least one side capable of observing the sandstone target inside the tube, and organic materials can be usedMade of glass, convenient for observing the rise of liquid level when saturated, with the vacuum tank suction port above,There is an inlet and outlet below, and the inlet and outlet should have a buffer filtration device to ensure that the liquid enters from the bottom of the target bodyFilter sand and impurities while entering and exiting the liquid; To increase the efficiency of vacuum extraction, at leastFour vacuum tanks work together, with each tank requiring an inner diameter of no less than 250mm and a height of no less than1000mm. Vacuum tank with vacuum gauge required.Figure 3 Schematic diagram of vacuum saturation tank3）Pump equipmentSalt water needs to be extracted from the storage tank and supplied to the vacuum tank. After saturation is complete, the inside of the vacuum tank should be emptiedExtract the liquid into the storage tank. The pumping equipment should be equipped with adjustable flow control valves to control the inflowLiquid velocity, to avoid the liquid level rising too quickly.4）Liquid storage tankUsed for configuring saturated liquids, storing saturated liquids, and soaking sandstone. The liquid storage device should be equipped with separate componentsZone, solution preparation zone, saturated sandstone target immersion zone (with at least 15 sandstone targets placed).The solution preparation area needs to be connected to the channel for pumping liquid into the vacuum tank and the cleaning and drainage channelInstall a filtering device to prevent impurities and sand from blocking the pipeline. The sandstone target immersion area should be easy to liftTake sandstone targets and ensure that the targets are isolated from each other to avoid collision.5）Convenient control cabinetNeed to control and set parameters for vacuum pumps and pump liquid equipment, with control switches and parametersThe numerical settings include vacuum value, holding time after vacuuming, timed shutdown, and vacuum compensationThe pump switches and inlet flow control valves of each pipeline are used for flow control.6）Other fixturesConvenient transportation gripper for target body (ensuring easy lifting and transportation of sandstone targets without damaging sandstone targets), electricSub scale (used for weighing dry and wet weight of sandstone targets, requiring a range of 200kg and an accuracy of 1g)Safety and environmental protection requirements1）Electrical equipment should be grounded to prevent static electricity accumulation;2）The equipment configuration should fully ensure reliability and maturity, with a reasonable layout and simple operation and maintenanceConvenient, ensuring safe and reliable operation;3）Liquid collection trays should be considered at the saturation device and pump to prevent the leakage of saturated liquid and pollution of the environment;4）Due to the medium being saltwater, corrosion-resistant materials should be considered for material selection.

1. Inner diameter of organic saturation cylinder: φ 250x1000mm4set

2.Vacuum pump 20m ³/h1platform

3.vacuum gauge-0.098MPa4only

4.High pressure valve DW612Only

5.High pressure shut-off valve DW65only

6.Pipeline process DW6/20MPa1Set up

7.Stainless steel inlet pump 10L/h1Taiwan Shanghai

8.Vacuum storage tank 2L1platform

9.Electric control 220V1set

10.Mobile bracket aluminum profile1set

11.Filter DW64a

12.Stainless steel core basket, diameter 200x1000mm4A