Electromagnetic sample grinder material bowl quenching treatment has strong wear resistance

Electromagnetic sample grinder material bowl quenching treatment has strong wear resistance

We have finished discussing the characteristics of electromagnetic ore crushers. Now, let's talk about the operation process of electromagnetic ore crushers

l、 Place the tube into the cup and place the small end facing downwards.

2. Place the sample, consisting of iron, limestone, slag, clinker, quartz, and clay at around 6Og. Coal weighs around 40g, with small sizes ranging from 15-20g.

3. Cover the cup lid on the material cup, paying attention to whether the O-ring seal on the lid is in good condition.

4. Place the cup into the host and then lower the pressure rod. Tighten the nut by hand, and be sure to have a gasket under the nut.

5. Tighten the nut with a wrench, then close the box cover, turn on the switch, set the timer to 2 minutes, and the machine will start working.

6. The machine stops working after the scheduled time. At this time, you can turn off the switch, open the box cover, loosen the nut, put on gloves, and take out the cup. After taking out the cup, place the cup cover in one corner of the sample tray, and pour the sample and tube into the sample tray together.

7. Use crucible tongs to clamp the material tube, and use a wrench to tap the material tube with the other hand. Repeat the tapping up and down several times, and the majority of the samples will fall into the sample tray.

8. Use a brush to further clean the remaining sample.

9. If there is adhesion or agglomeration on the inner wall of the cup due to high sample moisture or other reasons, a special shovel can be used to remove it.

Closed DF-4 Electromagnetic Ore Crusher - Laboratory New Generation Crusher Precautions

1. The voltage should meet the requirements. If the voltage is too low, it will cause the relay to fail to close properly and burn out. The power should be turned off immediately. When it is consistently below 210 volts. You can purchase a voltage regulator from our factory separately.

2. The ground wire must be in good condition.

3. If the moisture content of the sample is too high, it should be dried before grinding.

4. Cleaning of material cups: If specialized material cups are specified according to the variety, they do not need to be cleaned or can be simply cleaned. Users can purchase additional material cups as needed.

5. The cup of this machine generally does not need to be rinsed with water. If it is rinsed with clean water, it should be immediately placed in an oven for drying to prevent rusting.

6. Some users are accustomed to using the method of sample grinding to clean the cup and tube. They first take out a portion of the sample to be ground and discard it, and then take a formal sample for grinding. Alternatively, quartz sand or slag can be pre ground first to clean the crushing device. These methods may be necessary in particularly strict testing situations, but the pre ground material should not be too much or too little, and a time of 10 to 30 seconds is sufficient.

Electromagnetic sample grinder material bowl quenching treatment has strong wear resistance

Shanghai Leiyun specializes in producing electromagnetic ore crushers, with free shipping and a one-year warranty. If you have any questions about electromagnetic ore crushers, you can contact us and we will have professional electromagnetic ore crusher technicians to answer them for you

1. Electromagnetic ore crusher is a new type of sample crusher that uses the principle of electromagnetic suction to drive the material tube to quickly crush the material into fine states.

2. Without transmission components, it has small size, light weight, and long service life, especially suitable for users with small sample sizes.

3. Fast crushing speed, fully enclosed, eliminating the disadvantages of dust flying, it is an updated product of disc and eccentric rotating crushers

4. Suitable for inspection departments of coal, mining, cement, electricity, chemical, import and export commodities, quickly crushing various samples.

Overview:

The DF-4 electromagnetic ore crusher is a product launched by Shanghai Leiyun Testing Instrument Manufacturing Co., Ltd. Electromagnetic ore crusher, also known as electromagnetic ore crusher, is a new and efficient sampling tool that uses the principle of electromagnetic vibration to directly drive the vibrating tube to crush materials at high speed (3000 times/minute). It has the advantages of high efficiency, small size, light weight, no noise, and no dust. It can replace various sample crushers (and various mortars) to quickly prepare and analyze samples.

Scope of application:

Widely applicable to laboratories in various industries such as mining, building materials, cement, metallurgy, chemical, coal and grain. Especially for the preparation of fly ash samples from thermal power plants. The DF-4 electromagnetic ore crusher has been used by cement, mining, oil and chemical units, and has been tested by the National Cement Quality Supervision and Inspection Center. It has been proven to have excellent performance and is an ideal sample crusher. It is currently supervised by the National Cement Quality Supervision and Inspection Center and is being promoted and applied nationwide.

Features:

1. The DF-4 electromagnetic ore crusher is a new type of sample crusher that uses the principle of electromagnetic suction to drive the material tube to quickly crush the material into a fine state.

2. Without transmission components, it has small size, light weight, and long service life, especially suitable for users with small sample sizes.

3. Fast crushing speed, fully enclosed, eliminating the disadvantages of dust flying, it is an updated product of disc and eccentric rotating crushers

4. The DF-4 electromagnetic ore crusher is suitable for coal, mining, cement, electricity, chemical, and import and export commodity inspection departments to quickly crush various samples.