100A/2V-12V battery high current discharge meter

0-100A battery high current constant current discharge meter

WM-RS-F100A/2V-12V

Battery voltage 2V, 3.7V, 12V, 36V48V60V, 72V, 110220V five hundredV

everygodinstrument for drawing circlescheckequalapprovecalmmake

Technical Parameter

1.Discharge current: constant current of 10.00－99.99ACan be set.

2.Termination voltage:1.60V－15.00VCan be set. Customizable to be placed in0V

3.Battery voltage: nominal2-12VBattery. Discharge * low voltage1.6V

4.Operation mode: Constant current discharge.Constant power discharge,Constant resistance,Discharge fraction16paragraph,

Each paragraph can choose a loop of meaning,standing,discharge,Discharge Current,end voltage,The termination time can be set arbitrarily.

5.Discharge time: each segment1second-99hour59minute59Second x16Segments can be set.

When discharging, if either the termination voltage or termination time reaches the set value, the equipment will automatically move on to the next step of operation

(Static, discharge with another parameter, cycle, or stop discharging)

6.Cycle times:1-999order(×16paragraph)Can be set.

7.Work record: Automatic recording of results for each section of work point,Generate curve chart data table,Can view printing.

8.Remote monitoring: can be controlled by connecting to a computer,monitor,Can set time interval(1to3600Any value in seconds)

Automatically record and save printing operation data.

9.Test accuracy: better than ±0.5％(*A large number of journeys99.9A/19.99V).

10.Voltage input: ≤15V.

11.Discharge power: ≤ twenty00W

12.Overheating protection: ≥85Automatically pause discharge at ℃, ≤65Automatic continuous discharge at ℃.

13.Cooling method: air cooling.

14.Power input: single-phaseAC220V±10％，50Hz，≤80W.

15.Dimensions: Approximately wide660X deep600X high230mm.

16.Whole machine weight: approximately30kg.

0-100A computer-controlled high current constant current discharge instrument

WM-RS-F100A/2V-12V

The device is not connected to the computer and can be used independently

Display buttons on the LCD screen

R 1 6CV D 101 CV function →

↑U 13.00V U 11 .00V

●● ● I

100.0A I 100.0 Arun stop pause

99 : 59 : 59 99 :59 : fifty-nine●●●(answer12VThe battery is used

dischargetestExample usage operation method:)Connect the device to the power supply,But do not connect the discharged battery,Familiarize yourself with the setup method first,After checking for accuracy,After pressing the stop button to save,Turn off the electricitySource.Connect the discharged battery,Be careful not to reverse the polarity,

turn on power

,Press the run button,

Conduct experiments immediately.The meaning of the mode code displayed on the LCD screen in the upper right corner is as follows:①CV constant voltage charging, ② CA constant current charging, ③ CS to float charging, ④ FC reverse charging (

Only for chemical machine use) ⑤ FAConstant current discharge,⑥ FP constant power discharge ⑦ FR constant resistance discharge⑧ Ⅻ00cycle operation

,⑨JZstanding⑩end

This discharge machine only has

⑤⑥

⑦⑧⑨ ⑩ Six functions in bold fontShanghai Weiming 0-100A computer-controlled high current constant current discharge instrumentWM-RS-F100A/2V-12VConnect computer operation,Refer to the instruction manual for microcomputer control and monitoring software(

Website homepage click4' Data Download7'

downloadable8) auxiliary word for ordinal numbers9Page experiment parameters and process settings

auxiliary word for ordinal numbers

View page history tableauxiliary word for ordinal numbers

View page history chartauxiliary word for ordinal numbersPage chart printingDevice not connected to computer for independent use (example)Single-stage discharge3:30For example, it is necessary to carry out:Constant current discharge current

100.0A,putdivide

Second or reaching termination voltage

10.50V→The device automatically stops working.

1. PressfunctionPress the button to move the left cursor to the 1 on the right side of the data * * line segment number 101,Press the ↑ button twice to set it to 101 (i.e. * * stage). Press the ↑ button continuously to change the setting from 0 to 93. Press

functionPress the button to move the left cursor to the third data 00 (mode) on the right side of the data * * row *Press the ↑ button to select settings as needed-------

select

《FAConstant Current Discharge4. Pressfunction

Press the button to move the cursor to the data * * row U * * data (voltage 00.00) on the right side, and press the ↑ and → buttons,Select the charging voltage value of 10.50V as needed5. Press

function Press the button to move the cursor to the third row of I * * data on the right side

(On the current of 00.00, press the ↑ and → buttons to select the desired current value, such as 100.0A6. Press

function

Press the button to move the cursor to the fourth row * * data (working time) on the right, and press the ↑ and 3 buttons to select the desired time value. For example, 00:03:30 is 3 minutes and 30 secondsset up**Stage

1. Press againfunction00Press the button to move the cursor to the right side of data * * row * data 101 (segment number)

2. Press the ↑ button to set it to 102 (i.e. * * stage)3. PressfunctionPress the button to move the cursor to the third data 00 (mode) in the * * row on the right4. Press the ↑ button to select settings as needed----------------..Choose《End "

5. Then pressstop

button,Send out dropsSound confirmation storageThe cursor returns to * * rows * * data on the left siderun:pressrunPress the button to start working, and the left side of the LCD screen displays the voltage, current, and time values during the test process. The right side of the LCD screen displays the set voltage, current, and time values. At this point, the device conducts a discharge test on the battery. presspauseButton, pause discharge, press againrun Button, continue discharging ahead. press

stop

Button, stop discharging, press againrunButton, start discharging from scratch again.Work done,

The host LCD screen keeps displaying the voltage and time data at the end of shutdown.

After manually recording the voltage data and test data of each battery.Turn off the power switch first

,3Then remove the current cable from the battery30,*Remove the voltage sampling line afterwards.Multi-stage discharge

For example, it is necessary to carry out10:

1. Constant current discharge1dividesecond,Discharge termination voltage 11.00V, discharge current 10.00A → Automatic transition →2. Let it stand stillSplit → Automatic Transfer →3. Constant current discharge

hour10,3Discharge Current20.00A,,end voltage10.50V→ Automatic transfer →4. 'Standing still'Split → Automatic Transfer → Constant Current Dischargeminute,Discharge Current10.00A,9end voltage

10.50V30》,Continuous cycle2-3paceNext time → Automatic transfer →5. Constant current dischargesecond,

Discharge Current ** 100.0A,

Reaching the termination voltage6.00Vafter

,

The device automatically stops working.set upstage

1. PressfunctionPress the button to move the left cursor to the 1 on the right side of the data * * line segment number 101.Press the ↑ button twice to set it to 101 (i.e. * * stage), and press the ↑ button continuously to change the setting from 0 to 9.3. Press

functionPress the button to move the cursor to the third data 00 (mode) on the right side of the data * * row *.Press the ↑ button to select settings as needed-------

select《

FAConstant Current Discharge4. PressfunctionPress the button to move the cursor to the data * * row U * * data (voltage 00.00) on the right side, and press the ↑ and → buttons,

Select and set the charging voltage value as needed11.00V5. Press

function ** Press the button to move the cursor to the third row of I * * data on the right side

(On the current of 00.00, press the ↑ and → buttons to select the desired current value, such as 10.00A6. Press

function

Press the button to move the cursor to the fourth row of data on the right (working time), and press the ↑ and → buttons to select the desired time value, for example: 00:03:30, which is 3 minutes and 30 seconds.set upstage

1. Press againfunctionPress the button to move the cursor to 1 on the right side of data * * row * * data (segment number) 101.2. Press the ↑ button to set it to 102 (i.e. * * stage)3. Press

functionPress the button to move the cursor to the third data 00 (mode) in the * * row on the right4. Press the ↑ button to select settings as needed, ---------------

- Choose《 -JZ

Standing still5. Pressfunction

Press the button to move the cursor to the next row of * * data (working time) on the right side, press the ↑ and → buttons to select the desired time value, for example: 00:10:00 (i.e. 0 hours, 10 minutes, 0 seconds)

set upthirdstage

1. Press againfunctionPress the button to move the cursor to 2 on the right side of data * * row * * data 102 (segment number)2. Press the ↑ button to set it to 103 (i.e. the third stage)3. Press

functionPress the button to move the cursor to the third data 00 (mode) in the * * row on the right4. Press the ↑ button to select settings as needed-----------------

select《FAConstant Current Discharge5. Press

functionPress the button to move the cursor to the right data * * row U * * data (voltage), press the ↑ and → buttons to select and set the discharge termination voltage value as needed, for example, selecting 10.50V for a 12V battery6. Press

function Press the button to move the cursor to the third row of I * * data (current) on the right, and press the ↑ and → buttons to select and set the current value as needed

,For example, choose 20.00A7. Press

function

Press the button to move the cursor to the fourth row of data on the right (working time), and press the ↑ and → buttons to select the desired time value, for example: 01:00:00 is 1 hour, 00 minutes, and 0 secondsset upThe fourth stage

1. Press againfunctionPress the button to move the cursor to * * rows * * data (segment numbers) on the right side 2. Press the ↑ button to set to 04 (i.e. * * stage)

3. PressfunctionPress the button to move the cursor to the third data (mode) in the * * row on the right side of the data

4. Press the ↑ button to select settings as needed----------------Select 'XII'

Circular Work

5. Press again function

Press the button to move the cursor to the next line of data on the right and turn it on (starting from which segment in the loop). Select 02 (* * segment)6. Press againfunction

Press the button to move the cursor to the next line of data on the right. OF (cycle a few times) Select 009 (cycle 9 times)

The setting of 5 and 6 is to proceed from the above experiment to the third stage, and then from the second stage to the third stage after 9 cycles, to conduct the fifth stage experiment,set upStage 5

1. Press again functionPress the button to move the cursor to the right of data * * row * * 104 (segment number) on the right side 42. Press the ↑ button to set it to 105 (i.e. the fifth stage)

3. PressfunctionPress the button to move the cursor to the third data 00 (mode) in the * * row on the right4. Press the ↑ button to select settings as needed---------Choose《

FAConstant Current Discharge5. Press

functionPress the button to move the cursor to the right data * * row U * * data (voltage), press the ↑ and → buttons to select and set the voltage value as needed,

For example, selecting 0.6.00V for a 12V battery 6. Press

functionPress the button to move the cursor to the third row of I * * data (current) on the right, and press the ↑ and → buttons to select and set the current value as needed, for example, select 99.99A (100A)7. Press

function

Press the button to move the cursor to the fourth row of I * * data (working time) on the right, and press the ↑ button to select the desired time value. For example, 00:00:30 is 0 hours, 00 minutes, and 30 secondsset upStage 6

1. Press againfunction00Press the button to move the cursor to the right side of data * * row * * data 105 (segment number) 5

2. Press the ↑ button to set it to 106 (i.e. the sixth stage)3. PressfunctionPress the button to move the cursor to the third data 00 (mode) in the * * row on the right4. Press the ↑ button to select settings as needed----------------..Choose《End "

5. * Press againstop

button,Send out dropsSound confirmation storageThe cursor returns to * * rows * * data on the left siderun:pressrunPress the button to start working, and the left side of the LCD screen displays the voltage, current, and time values during the test process. The right side of the LCD screen displays the set voltage, current, and time values. At this point, the device conducts a discharge test on the battery. presspause

Button, pause discharge, press againrun Button, continue discharging ahead. press

stop

Button, stop discharging, press againrunButton, start discharging from scratch again.Work done,

The host LCD screen keeps displaying the voltage and time data at the end of shutdown.After manually recording test data such as battery voltage.Turn off the power switch first