+GF+Signet integrated rotary flow meter in large stock

+GF+Signet integrated rotary flow meter in large stock

The 2537 rotary flowmeter series features low flow rate, low power, and high resolution, with various output options such as volume pulse

Pulse frequency divider, flow switch, digital (S3L) or 4-20 mA. It can be directly accessed through the built-in user interface

Set up the unit on site.

The 4-20 mA model provides blind current loop output.

The digital (S3L) model provides digital (S3L) output for connecting Signet 8900 multi parameter control

Device or 9900 transmitter.

The composite model uses a single relay (mechanical or solid-state) and has three optional operating modes:

The frequency divider mode can reduce the wheel frequency to adapt to devices with low-frequency inputs.

The accumulation mode can achieve one pulse output for each group of traffic.

The flow switch mode uses a single relay and can perform high or low alarm operations.

A small LCD can be set up on the 2537 without using any external devices. During normal operation period

The display is not visible.

Planting liquids and chemicals.

All plastic materials (including typical pipe types such as PVC, PVDF, PP, etc.)

PE) is more or less permeable to the medium it contains, such as water or volatile compounds

Quality, including some acidity. This effect is not related to porosity, but purely gas permeability

The problem of plastic diffusion.

If the plastic material is compatible with the medium, penetration will not damage the plastic itself. but

Yes, if the plastic contains other sensitive components such as GF Signet plastic wheel conveyors

Sensors may be affected by the diffusion of media into the body and rotor

Or damaged.

There have been reports of PVDF wheel sensors malfunctioning in hot nitric acid applications.

PVDF allows nitric acid components to penetrate without damaging itself. There's no clear here

Accurate guidelines, as the destructive effect on sensors largely depends on

Temperature, pressure, and medium concentration.

It is possible to apply sensors in corrosive media. GF Signet can

Provide sensors with special requirements, whose different internal resin encapsulation can delay acid

The destructive effect on sensors.

Wheel maintenance:

The wheel on the sensor is prone to wear and may require repair and replacement of components (wheel,

Rotating shaft, O-ring, bearing, cage, etc. The maintenance cycle depends on the application environment

It depends on the environment, medium characteristics, and installation. Including but not limited to: process flow rate, water hammer

The appearance of corrosive and abrasive fluids, as well as the surrounding equipment where sensors are installed.

GF Signet provides separate replacement parts and wheel replacement kits, including replacement operations

Provide an instruction manual that allows customers to perform on-site replacement to reduce system downtime.

+GF+Signet integrated rotary flow meter in large stock

Product Specifications

General Specifications

Flow velocity range ..........................0.1 m/s - 6 m/s

Pipe diameter range .........................DN15 - DN200 (½ in. - 8 in.)

Minimum Reynolds number .....................4500

Wiring port 1/2 inch NPT thread; Liquid tight joint can be connected

Receiving electricity with an outer diameter of 7mm-10mm

缆 （0.275in.-0.394in.）

material

shell ........................................PBT, yellow

Inner shell .......................................Valox, black

Liquid receiving material

-P0, -P1

Sensor body Fiberglass filled polypropylene

O-ring ..............................FKM

Rotating shaft Titanium

Wheel ..................................PVDF， Black; Optional ETFE, with or

Without carbon fiber reinforced PTFE shaft sleeve

-T0

Sensor body ....................PVDF, natural color

O-ring ..............................FKM

Rotating shaft .................................PVDF, natural color

Wheel ..................................PVDF， natural color; Optional ETFE, with

Or without carbon fiber reinforced PTFE shaft sleeve

performance

Input frequency range .........................1 - 1000 Hz

System response The nominal refresh rate is 100ms

Wheel frequency Nominal 49Hz per m/s

Linearity ± 1% of the measuring range

@ 25 °C (77 °F)

Repetitive accuracy ± 0.5% of the measuring range

@ 25 °C (77 °F)

electricity

Relay specifications

Dry contact SPDT...... 5 A @ 30 VDC, 5 A @ 250 VAC

Solid state relay ...........................100 mA @ 40 VDC,

70 mA @ 33 VAC

Power requirements

Complies with:

Equipped with dry contact relay ...... Nominal 24VDC ± 10%, stabilized voltage,

Current 30mA

Equipped with solid-state relays ...... Nominal 5-24VDC ± 10%, stabilized voltage,

Current 30mA

Number (S3L).................................. 5.0-6.5VDC, current 30mA

Nominal 1.5mA)

4-20 mA............................. Ripple voltage 400mV

Current 30mA

Reverse polarity and short circuit protection ...... Up to 40V, 1 hour

Overvoltage protection 40 VDC for more than 1 hour

output

Signal damping Can be set from 0 to 100 seconds

Sensitivity response Can be set to 0-9 degrees

Pulse divider/total pulse output

Pulse divider setting ................. 1.0000 - 99999

Pulse rate ...................... 300 Hz

Pulse width ................. 50 ms

Flow switch output

Relay mode Low, high

Delay .................................. 0.0-6400.0 seconds

Delay Adjustable

wiring

Only qualified personnel are allowed to operate the electrical connections of this product.

To use wiring terminals:

1. Rotate the yellow lid counterclockwise by ¼ circle to remove it.

2. Remove the two fixing screws and then remove the black cover plate.

Before connecting the cables to the terminals, please thread all cables through the conduit ports.

The terminal block is suitable for wires with 16-22AWG specifications.

The cable diameter must be 7 mm to 10 mm (0.275 in. to 0.394 in.) to ensure proper sealing in the liquid tight joint.

3. The conduit port has a 1/2-inch NPT thread. After wiring, seal the port with a liquid tight conduit connector (3-9000.392-1) or conduit.

For the installation of conduit:

The threaded conduit has a half inch NPT thread, which can be directly connected to the conduit port.

For conduit with ISO threads, please use the black thread adapter included with the connector kit.

To comply with NEC requirements, do not use any metal conduit during installation.

Manufacturer Part Number Order Code Description

2537 system for 0.5-4-inch pipelines:

Polypropylene body, black PVDF wheel, titanium shaft, FPM O-ring

159 001 291 pulse/flow switch, DCR，-P0， Integrated installation

159 001 292

159 001 295

3-2537-1C-P0

3-2537-2C-P0

3-2537-5C-P0

3-2537-6C-P0 159 001 296

Pulse/flow switch, SSR，-P0， Integrated installation

Digital (S3L), integrated installation

4 - 20 mA, Integrated installation

2537 system for 5-8-inch pipelines:

Polypropylene body, black PVDF wheel, titanium shaft, FPM O-ring

159 001 303 pulse/flow switch, DCR，-P1， Integrated installation

159 001 304

159 001 307

3-2537-1C-P1

3-2537-2C-P1

3-2537-5C-P1

3-2537-6C-P1 159 001 308

Pulse/flow switch, SSR，-P1， Integrated installation

Install digital S3L, integrated

4 to 20 mA, Integrated installation

2537 system for 0.5-4-inch pipelines:

Natural color PVDF body, natural color PVDF wheel and shaft, FPM O-ring

159 001 315 pulse/flow switch, DCR，-P0， Integrated installation

159 001 316

159 001 319

3-2537-1C-T0

3-2537-2C-T0

3-2537-5C-T0

3-2537-6C-T0 159 001 320

Pulse/flow switch, SSR，-P0， Integrated installation

Digital (S3L), integrated installation

4 - 20 mA, Integrated installation

Attachment

Manufacturer Part Number Order Code

3-2536.320-1 198 820 052

3-2536.320-2 159 000 272

3-2536.320-3 159 000 273

3-2536.321 198 820 054

3-2536.322-1 198 820 056

3-2536.322-2 198 820 057

3-2536.322-3 198 820 058

M1546-1 198 801 182

M1546-2 198 801 183

M1546-3 198 820 014

M1546-4 198 820 015

P51545 198 820 016

1220-0021 198 801 000

1224-0021 198 820 006

1228-0021 198 820 007

P31536 198 840 201

3-8050.390-1 159 001 702

3-8050.390-3 159 310 116

3-8050.390-4 159 310 117

3-9000.392-1 159 000 839

3-9000.392-2 159 000 841

7310-1024 159 873 004