Product Categories

Shenzhen Kyoto Yuqi Electronics Co., Ltd

E-mail
Phone
Address
3rd Floor, E-commerce Building, No. 906 Meilong Avenue, Songhe Community, Longhua Street, Longhua District, Shenzhen

Contact Now

Wind speed of 0.001 m/s instead of anemometer SONIC Sonic

NegotiableUpdate on 05/06

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

The WAM-100 ultrasonic anemometer can obtain highly reliable data by digitally sampling and internally processing the ultrasonic waveform. Not limited to cleanrooms, it can also be used for high-precision airflow (breeze) monitoring in LCD panels, LED production lines, living environments with constantly changing temperatures, and internal airflow monitoring in refrigerators. $r $n wind speed of 0.001 m/s instead of anemometer SONIC Sonic

Product Details

Wind speed of 0.001 m/s instead of anemometer SONIC Sonic

3. Specifications

Measurement method: Time division transmission and reception switching ultrasonic pulse mode
Calculation method: reciprocal difference calculation method of ultrasonic propagation time
Measurement range:

Wind speed: 0-10 m/s
Acoustic virtual temperature: -30 to+50 ℃

Measurement accuracy:

Wind speed: ± (10% of measured value+0.05 m/s) * ¹, * ²
Wind direction: ± 10 ° * ¹, * ²
Acoustic virtual temperature: ± 5 ℃ (when there is no wind)

Output resolution:

Wind speed: 0.001 m/s
Acoustic virtual temperature: 0.01 ℃

Calculation cycle: 10 times/second
Responsiveness: Less than 5 seconds
Digital output:

Output format: RS-422 (converted to USB through a matching cable)
通信速率： 9600 bps
Output rate: 10 times/second
Data format: ASCII 6 bytes/measured component
Output data: A, B, C, T+³

Usage environment:

WAM-100 host: 0~+50 ℃, 20~80% RH
Probe: -30~+50 ℃, 20-80% RH

(All devices must not condense; there should be no obstacles such as water droplets or ice on the probe head)

Power supply: DC 12V/0.5A (DC 9.6-17V)

*After zero point calibration, within ± 20 ° of the main wind direction

*When using the supporting software WASP-007F and enabling the smoothing function

*T is the acoustic virtual temperature (the average of the three acoustic virtual temperatures Ta, Tb, Tc measured on the A, B, and C axes)

4. Composition

Anemometer host: WAM-100 1 unit
Probe: TR-93T 1 unit
Connecting wire: JSC-18 (1.7m) 1 piece
AC adapter: ACADP-12 1 piece
3D airflow visualization software: WASP-007F 1 set
Probe installation bracket: 1 piece
Zero calibration cover: 1 set
Portable case: 1 unit

Attention

The computer supports Windows 10 64 bit version and Windows 11.

5. System composition

The WAM-100 ultrasonic anemometer consists of the following parts.

Attention

The anemometer host stores probe specific parameters, so the host and probe must be used in pairs (please confirm that the serial numbers on the nameplates of each device are consistent).

5.1 Overall Composition

(Omitted, corresponding to the position of the original schematic diagram)

5.2 Probe characteristics and combinations

The TR-93T probe is a three directional probe with a main wind direction limiting type, and the measurement spacing is miniaturized to 2 cm. It is mainly used for wind tunnel model experiments, indoor airflow observation such as air conditioning, etc.

The TR-93T measures wind direction within ± 20 ° of the main wind direction.

Maximum measured wind speed: 10 m/s

Measurement axis spacing: 2 cm
Measuring wind direction range: within ± 20 ° of the main wind direction
Measure wind speed components: A, B, C axes
Purpose: Indoor breeze observation, etc
Measurement accuracy: ± (10% of the measured value+0.05 m/s)

(Within the range of ± 20 ° of the main wind direction after zero point calibration)

6. Names and functions of each part

6.1 WAM-100 Host

Power switch: used for turning on/off the local power supply (I)/off (O)
Probe connector: used to connect TR-93T probes
POWER LED: displays the power on status of the device

Green constantly on: power on/normal power on
Red light on: Input voltage warning (power supply voltage drops by 10%)
Red light on: Abnormal input voltage (power supply voltage below rated value)
Extinguish: Power off/no power supply

Status LED: displays the measurement/communication status of the device

Green: Power on preheating
Green: Normal measurement
Green: Zero calibration (running during zero reset)
Extinguish: Measurement stopped
Red: Data missing
Red: Hardware error (cable not connected, device failure, etc.)
Red: Communication error

Zero reset switch: used for zero calibration after probe connection

After covering the probe with the zero calibration cover to form a windless state, press and hold the switch for more than 3 seconds, the STOP LED will flash green at high speed, and zero calibration will begin; After calibration is completed, the LED remains green and constantly on.
DC IN connector: used to connect AC adapter ACADP-12
Grounding terminal: used to connect the grounding wire (using screw: M2.6L4)
SYSTEM PORT-1 connector: used for connecting the host to the computer

Special connecting wire JSC-18 must be used, and the use of commercially available cables is strictly prohibited.
SYSTEM PORT-2 connector: used for connecting multiple WAM-100 hosts

(For multi machine connection matters, please consult our company)