Straightening and wire cutting machine (3mm-6.5mm)

The straightening and cutting machine (3mm-6.5mm) is used for straightening and cutting steel bars with a diameter of 3-6.5mm. The cutting length can be customized according to customer requirements. Adjustable straight cutting of stainless steel wire, aluminum wire, cold drawn wire, galvanized wire, iron wire, steel wire, steel bar, plastic coated steel wire, etc., with neat cutting, small error, and good performance.
Construction: The straight wire machine consists of a straightening cylinder, a traction mechanism, a cutting mechanism, a steel bar fixed length frame, a frame, and a driving device.
This machine consists of an inlet section, a straightening section, a cutting section, etc. Its linear gun can automatically cut the wire to a fixed length and automatically drop the material. After loading, the machine performs automated operations. The machine has a reasonable structure, stability and reliability, simple operation, high degree of automation, and operators can manage multiple machines at the same time, greatly improving production efficiency. It is a necessary specialized equipment for hardware, network cable and other manufacturers.

Construction: The straightening machine consists of a straightening cylinder, a traction mechanism, a cutting mechanism, a steel bar fixed length frame, a frame, and a driving device.

Operating principle: The motor is driven by a belt to increase the speed, causing the straightening cylinder to rotate at high speed. The steel bars passing through the straightening cylinder are straightened, and the rust on the surface of the steel bars is removed by the straightening die; Driven by an electric motor through another pair of reduction belts and a gearbox, it drives two conveying pressure rollers to pull the steel bars forward, and drives the crank wheel to move the hammer head up and down. When the steel bars are adjusted to the predetermined length, the hammer strikes the knife holder to cut the steel bars. When the cut steel bars fall into the receiving rack, due to the action of the spring, the knife holder returns to its original position, completing one cycle.

Installation and Debugging

1. This machine should be installed on a relatively flat foundation, and some soft cushions should be placed on the foundation to prevent the machine from high-speed and ground vibration;
2. The host is connected to the slide on the same straight line, until it is the smoothest;
3. Rotate the punch head by hand to see if it is engaged with the cutting assembly. If it is not engaged, adjust the height of the slide rail bracket pulley;
4. Durable slide limit lock plate;
5. Connect the slide spring;
6. The motor on top is consistent with the cutting wheel tip;
7. Adjust, slowly bend, increase the angle of the middle three pieces, and if there is a bean grain bend, reduce the angle;
8. Adjust the slider inside the slide to the size you need (measured from the bottom of the cutting section), and tighten the slider with screws.

serial number	name	unit	Specifications
1	Adjust the diameter of the straight material	millimeter	3.0-6.5
2	Automatic cutting length	centimeter	10 － 1200
3	Straightening speed	Meter per minute	25 － 30
4	Adjust the speed of the straightening cylinder	Conversion/Minute	1964.5
5	Straighten and cut off the motor	kilowatt	2.2× 3.0
6	machine weight	kilogram	150
7	Dimensions (length x width x height)	millimeter	1100 × 380× 980
8	This machine is suitable for straightening and cutting metal wires such as steel bars, alloy wires, iron wires, and metal wires

Fault handling

Bending wire: Adjust the angle of the straightening block, check whether the straightener and the rolling groove, and cut the assembly are in a straight line.

Broken wire: The straightening block angle is too large, the compression spring on the cutting assembly becomes soft, the knife cannot retract, the compression spring on the wire feeding roller is too loose, and the material is not good.

Running wire: The rolling spring is too tight, the tension spring of the slide is too loose, the steel rod for dragging wire under the slide is not in place, and the slide does not slide.

Short section: The tension spring between the slide and the host is too loose. Adjust the tension spring.

Machine vibration: Adjust the balance of the straightening block.

The straightening and cutting machine (3mm-6.5mm) is used for straightening and cutting steel bars with a diameter of 3-6.5mm. The cutting length can be customized according to customer requirements. Main production: straightening machines, wire straightening machines, wire cutting machines, straightening and cutting machines (suitable for cutting: iron wire, galvanized wire, stainless steel wire, steel wire, steel bars, cold drawn wire, etc.), as well as various wire mesh machinery such as wire drawing machines and welding machines.