Specification of human pulmonary microvascular endothelial cells

1、 Basic cellular properties

Organizational source: Lung tissue

Species source: Human

Cell Introduction:Human pulmonary microvascular endothelial cellsSeparate from lung tissue; The lungs are the respiratory organs of the body, located in the chest cavity, one on each side, covering the heart. The lungs have lobes, two on the left and three on the right, totaling five lobes. The lung meridian system (referring to the trachea, bronchi, etc.) is connected to the larynx and nose, hence the larynx is called the gateway to the lungs, and the nose is the extrapulmonary orifice. Microvascular endothelial cells are closely involved in a series of physiological and inflammatory responses, including regeneration, development, and wound healing. The cells are spindle shaped or polygonal, and after forming a single layer, they are arranged in a cobblestone like or cobblestone like pattern. Pulmonary microvascular endothelial cells form a semi selective barrier, which is of great significance for lung gas exchange, regulating the flow of fluids and soluble substances between blood and lung interstitium.

Packaging conditions: PLL (0.1mg/ml), gelatin (0.1%)

Culture medium: containing FBS, growth additives, Penicillin, Streptomycin, etc

Fluid change frequency: Change the fluid every 2-3 days

Growth characteristics: Wall adhesion

Cell morphology: endothelial cell like

Passage characteristics: Can be passed down for 2-3 generations

Passage ratio: 1:2

Digestive fluid: 0.25%

Cultivation conditions: Air, 95%; CO2，5%

2、 Cell culture status

Send electronic photos of cells during shipment

3、 Usage method

Human pulmonary microvascular endothelial cellsIt is a type of adherent cell with an endothelial cell like morphology. Under the standard operating procedures of the technical department, the cell can pass through 2-3 generations; We suggest that you conduct relevant experiments as soon as you receive the cells.

After receiving the cells, please proceed with the following steps for the customer.

1. Take out the T25 cell culture bottle, disinfect the bottle body with 75% alcohol, remove the sealing film, and place it in a cell culture incubator at 37 ℃, 5% CO2, and saturated humidity for 3-4 hours to stabilize the cell state.

2. Digestion of adherent cells

1) Suck out the culture medium from the T25 cell culture bottle and wash the cells once with PBS;

2) Add 1mL of 0.25% digestive solution to the T25 culture bottle, gently rotate the bottle until the digestive solution covers the entire bottom of the bottle, then aspirate excess digestive solution and incubate at 37 ℃ for 1-3 minutes; Observe under an inverted microscope, wait for the cells to shrink and become round, then add 5ml of culture medium to terminate digestion;

3) Gently blow and mix with a straw, inoculate T25 culture bottles according to the passage ratio for passage, then add fresh culture medium to 5mL, and incubate in a cell culture incubator at 37 ℃, 5% CO2, and saturated humidity;

4) After the cells adhere to the wall, culture and observe; Afterwards, replace the fresh culture medium according to the frequency of fluid exchange.

3. Cell detachment upon receipt

1) Collect all cell suspensions, centrifuge at 1000rpm for 5 minutes, and retain the precipitate;

2) Add 0.5mL of 0.25% digestive solution to a centrifuge tube, resuspend the precipitate, and let it digest at 37 ℃ for 3 minutes (or let it stand in a refrigerator at 4 ℃ for 5-7 minutes); After digestion, add 5ml of culture medium into the centrifuge tube to terminate digestion;

3) Centrifuge at 1000rpm for 5 minutes, discard the supernatant, resuspend the precipitate in 5ml of culture medium, and inoculate it into a new culture bottle;

4) After the cells adhere to the wall, culture and observe; Afterwards, replace the fresh culture medium (preheated at 37 ℃) according to the frequency of fluid exchange.

5) The adherent cells in the original bottle were digested normally.

4. Cell experiments

Due to the special nature of primary cell adhesion, when the adherent primary cells are transferred to other experimental vessels (such as glass slides, culture plates, confocal culture dishes, etc.) after digestion, the experimental vessels need to be wrapped to enhance cell adhesion and avoid cells from affecting the experiment due to poor adhesion; The coating conditions are often selected as mouse tail collagen I (2-5 μ g/cm2), polylysine PLL (0.1mg/ml), gelatin (0.1%), depending on the cell type. Suspended/semi suspended cells do not require encapsulation.

4、 Precautions

1. The cultivation can be stored for 3-6 months under 4 ℃ conditions.

During the cell culture process, please pay attention to maintaining aseptic operation.

During the subculture process, digestion time should not be too long, otherwise it will affect cell adhesion and growth status.

4. It is recommended that customers take several cell photos for each magnification within the first 3 days after receiving the cells, recording the cell status for communication with the technical department; Due to transportation reasons, some sensitive cells may experience instability. Please contact us promptly and provide detailed information about the specific situation of the cells, so that our technical personnel can track and follow up until the problem is resolved.

The products currently being sold by the company: