Shanghai New Dawn BZD129 Intelligent Explosion proof LED Dimming Light

NegotiableUpdate on 05/13

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

Shanghai New Dawn BZD129 Intelligent Explosion proof LED Dimmer $r $n1, Explosion proof and Anti corrosion All Plastic Fluorescent Lamp BYS-2 * 18W. The shell is molded with SMC, and the lampshade is injection molded with polycarbonate, which has high strength, can withstand strong impact, and has strong corrosion resistance; $r$n2、 The lampshade is made of imported materials and has high light transmittance and anti UV aging function; $r$n3、 The lamp adopts a curved sealed structure, which has strong waterproof and dustproof functions;

Product Details

Shanghai New Dawn BZD129 Intelligent Explosion proof LED Dimming LightShanghai New Dawn BZD129 Intelligent Explosion proof LED Dimming Light

1、 Applicable places

1. Environmental temperature -25 ℃~+55 ℃;

2. The installation height shall not exceed 2000m above sea level;

3. Suitable for environments with weak acids, weak bases, salt, ammonia, chloride ion corrosion, high water, high dust, and humidity;

4. Suitable for places such as petroleum, chemical, food, medicine, warehouses, etc;

5. Mainly used as factory lighting, especially suitable for workshop lighting with corrosive gases.

　　2、 Performance characteristics

1. The explosion-proof and anti-corrosion all plastic fluorescent lamp BYS-2 * 18W adopts SMC compression molding for the shell, and polycarbonate injection molding for the lampshade, which has high strength, can withstand strong impact, and has strong corrosion resistance;

2. The lampshade is made of imported materials and has high light transmittance and anti UV aging function;

3. The lamp adopts a curved sealed structure, which has strong waterproof and dustproof functions;

4. The built-in ballast is an explosion-proof electronic ballast specially designed by our company, which has short-circuit and open circuit protection functions. It is equipped with a preventive circuit to prevent the aging effect and leakage of the lamp tube, so that the lamp can work normally and efficiently save energy with cos π≥ 0.95; It has a wide voltage input, operates normally within the voltage range of 170V-250V, and can maintain constant power output without affecting the output light efficiency;

5. Built in isolation switch, automatically cuts off power when the product is turned on;

6. The use of ordinary T8 fluorescent tubes reduces maintenance costs for users;

7. Emergency devices can be installed according to user requirements. When there is a power outage outside, the lighting fixtures will automatically switch to emergency lighting mode;

8. Execution standards: GB3836.1-2000, GB3836.2-2000, GB3836.3-2000, GB3836.9-1990.

3、 Technical parameters

1. Execution standards: GB3836.1, GB3836.2, GB3836.3, GB3836.9, GB12476.1, IEC60079

2. Explosion proof mark: Exd IIC T5/DIP A20 TA, T5

3. Rated voltage: AC 220V

4. Equipped with light source: T8 dual foot fluorescent tubes (1x36W, 2x36W) T5 dual foot fluorescent tubes (1x28W, 2x28W)

5. With emergency function parameters: charging time ≤ 24 hours, emergency start time ≤ 0.3 seconds

6. Emergency lighting time: 90 minutes

7. Protection level: IP65

8. Anti corrosion grade: WF2

9. Inlet thread: 3-G3/4 '

10. Cable outer diameter: Ø 9mm - Ø 14mm

　　4、 Installation and maintenance

1. When installing and maintaining lighting fixtures, it is strictly prohibited to turn them on when they are live;

2. The sealing ring of the introduction device should ensure reliable compression and clamping of the cable;

3. Regularly inspect the sealing ring and replace it promptly if it is found to be aging;

4. Just open the buckle on the outside of the shell and open the lampshade to connect the wires;

5. Before putting the lighting fixtures into use, they must be firmly grounded both inside and outside, and reliably connected to the user's on-site grounding system;

6. Please use blocking plates and compression nuts to reliably seal any unnecessary inlet ports on the lighting fixtures, ensuring explosion-proof performance and protection level performance;

7. The emergency battery of the explosion-proof and anti-corrosion all plastic fluorescent lamp BYS-2 * 18W is in an empty state when it leaves the factory. Users should fully charge it before normal use.