salt spray test chamber

Programmable artificial sweat test chamber, salt spray test machine, spray test machine

Characteristics of salt spray test chamber:
1： Body material:
1: 5MM imported gray white P.V.C board
2: Support frame: 10.0mm tempered glass rod with corrosion resistance. Place the plastic steel V-shaped frame and glass rod at a 30 degree angle to ensure that the test object is angled
3: Body bracket: SECC channel steel with angle iron spray painted Four wheel sliding Can be pushed and walked (limited to models 120 or above)
4: The pressure drum is made of seamless welded 2.0MMSUS201 stainless steel plate.
6: Titanium tubes are used for heating Long service life and high corrosion resistance
7: The hood is made of 5MM imported transparent acrylic board Exquisite workmanship, beautiful appearance, high transparency
2： Body specifications (JK-60A): Inner box size: 600 * 450 * 400 (L * M * H) Outer box size: 710 * 560 * 560 (L * M * H)
3： Control system:
1. DHC temperature controller, digital display PID automatic calculation, SSR output, high stability platinum temperature probe. The temperature during the salt spray test was mistakenly set to ± 1 ℃.
2. The pressure tank adopts Henry's law and is heated and humidified to achieve a laboratory humidity of over 95%, which meets national standards.
4： Timing system: adopting high-precision multifunctional timer, the test time can be set with multifunctionality, and can be set from 0.001S to 999.9H. It has power outage memory function, which can take photos of power outage after power on
Continue working until the product is completed within the required time frame to avoid redoing the experiment after a power outage.
5： Water replenishment system: adopting automatic/manual water replenishment system, with automatic/manual water replenishment function when the water level is insufficient. The experiment is uninterrupted, meeting the diverse environmental requirements of customers. (Automatic)
Water replenishment only needs to be connected to the tap water pipe
6： Heating method: During the salt spray experiment, steam direct heating method is used, which has a fast heating speed, uniform temperature distribution, and reduces standby time.
7： Control mode: Five key standard operation Equipped with a full detection fault warning system. The light can be turned on when a malfunction occurs The five key operation includes a power switch, an operation switch, and a spray
Fog switch, timer switch, and defogging switch. During the experiment, turn on the power switch and the instrument will automatically add water. After adding water, turn on the operation switch Set the experimental temperature and the instrument will automatically heat up
Turn on the spray switch to start the spray of the instrument, turn on the timing, set the time, and end the experiment after the completion of the time Built in manual defogging function Products can be placed or viewed during the experimental process
Remove the accumulated salt spray from the experiment.
8： Safety protection device:
1. Equipped with dual over temperature protection, it can automatically cut off the heating power supply in case of temperature control meter failure or heating system failure. Avoid damaging the instrument due to excessive temperature.
2. Double low water level protection to prevent dry burning and damage to laboratory and pressure drum heating pipes.
3. Equipped with overload and short circuit protection. Prevent damage to instruments and internal electrical control components in case of abnormalities If any low water level occurs, the machine alarm will turn on and beep to prompt! Is it convenient
Can be detected in a timely manner next to the machine!
9： Measuring cylinder: Two built-in fog collection cylinders (one JK-60 type) are used. Compared to traditional external models, it is less prone to damage.
10： Nozzle: Precision quartz glass nozzle Ensure no crystallization after 4000 hours of use The spray tower is equipped with a conical disperser, which can guide fog, regulate fog saving, and even fog falling
Function.
11： Sealing method: The inner and outer boxes are connected to a sealing groove and sealed with water Prevent salt spray leakage

12： Control panel and electrical accessories: Temperature controller (DHC), two pressure gauges (Taiwan), one indicator light (Taiwan), six timers (OMRON), one accumulator (Anliang), one control switch (Taiwan), five SSRs (Taiwan Yangming), two relays (Japan Omron), three temperature sensing wires (Taiwan Shenjie), two adjusters
Pressure valve (AIRTAC), two solenoid valves (AIRTAC), four water level gauges (Xiangyang, Taiwan), four heating pipes (titanium pipes), two EGOs, one
13： Attachment Description: Four V-shaped support racks (60 type), eight O-shaped support rods (60 type), two bottles of sodium chloride, 5000ML measuring cups, one pH test paper, two packs of 50ML measuring cylinders
One (Type 60)
14： Temperature range:
1: Laboratory temperature: 35 ℃ -50 ℃ (can be set arbitrarily)
2: Pressure bucket temperature: 47 ℃ -63 ℃ (can be set arbitrarily)
15： Heating rate:
1: Laboratory, room temperature ->35 ℃ for about 35 minutes
2: Pressure bucket, room temperature ->47 ℃ for about 15 minutes
16： Temperature accuracy: ± 1 ℃ Seventeen: This machine is suitable for neutral salt spray testing (NSS) and corrosion testing (AASS, CASS).
·Usage standard: CNS3627、3885、4159、7669、8886、JIS D-0201、H-8502、H-8610、K-5400、Z-2371、ISO 3768、3769、3770、ASTM B-117、B-268、GB-T2423、GJB 150. Built in features:
Salt water spray testing machine is suitable for surface treatment of various materials, including coating, electroplating, organic and inorganic film, anodic treatment, anti rust oil, etc
Corrosion resistance of the product.