- Phone
-
Address
No. 16, Lane 3788, Wenxiang Road, Songjiang University City, Shanghai
Product Categories
Shanghai Hengyu Instrument Co., Ltd
Oil heating open mill
NegotiableUpdate on 05/06
- Model
- Nature of the Manufacturer
- Producers
- Product Category
- Place of Origin
Overview
The advantage of an oil heating open mill is that it heats up quickly and evenly. When users have very uniform temperature requirements, an open mill with oil circulation heating is a good choice.
Product Details
HY-160YB oil heating open millSimple explanation:
1. Mixing capacity: about 0.1-2kgs
2. Roller temperature: Room temperature~+200 ℃ (If higher temperature is required, please specify before ordering.)
3. Temperature control method: circulating oil heating.
4. Temperature display: degrees ± 1 ℃
5. Number of motors: 1 unit
6. Front roller speed: 10-30r/min, adjustable.
Note: This machine uses a frequency converter to control the motor speed. When an overload condition occurs, the motor power supply is automatically cut off to protect the motor's lifespan as much as possible!
7. Front and rear roller speed ratio: 1:1.4
8. Roller size: ф 155mm × L350mm, surface coated with hard chromium, surface polished with mirror finish.
9. Roller spacing: adjustable from 0.1 to 6mm This machine is equipped with a powerful handle that can adjust the spacing between the rollers during rubber mixing.
10. Safety device:
A. There is a safety lever at the top, which stops immediately upon contact;
B. There are safety tapping devices on the left and right sides of the front and rear, with a tapping stop and reverse 1/4-1/3 turn device;
C. Front and rear knee collision safety device, knee collision stop and reverse 1/4-1/3 turn device
11. Roller lubrication: wear-resistant bearings are used
12. Bearing cover: Separate the exposed surface of the bearing to prevent rubber samples from entering the bearing chamber and extend the service life of the bearing;
13. Material baffle: The width can be flexibly adjusted, and the amount of rubber material can meet the requirements Less adhesive material, adjust towards the middle, and more adhesive material can be adjusted towards both sides.
14. Material receiving basin: Made of stainless steel, easy to clean, pollution-free and rust free.
15. Mechanical structure: Steel plate (lighter weight, smaller volume, higher mechanical strength, and better toughness than traditional cast iron)
16. Volume: (W × D × H) 1200 × 550 × 1300mm
17. Power supply: 3 ∧, AC380V，15A
18. Weight: Approximately 620kg
1. Mixing capacity: about 0.1-2kgs
2. Roller temperature: Room temperature~+200 ℃ (If higher temperature is required, please specify before ordering.)
3. Temperature control method: circulating oil heating.
4. Temperature display: degrees ± 1 ℃
5. Number of motors: 1 unit
6. Front roller speed: 10-30r/min, adjustable.
Note: This machine uses a frequency converter to control the motor speed. When an overload condition occurs, the motor power supply is automatically cut off to protect the motor's lifespan as much as possible!
7. Front and rear roller speed ratio: 1:1.4
8. Roller size: ф 155mm × L350mm, surface coated with hard chromium, surface polished with mirror finish.
9. Roller spacing: adjustable from 0.1 to 6mm This machine is equipped with a powerful handle that can adjust the spacing between the rollers during rubber mixing.
10. Safety device:
A. There is a safety lever at the top, which stops immediately upon contact;
B. There are safety tapping devices on the left and right sides of the front and rear, with a tapping stop and reverse 1/4-1/3 turn device;
C. Front and rear knee collision safety device, knee collision stop and reverse 1/4-1/3 turn device
11. Roller lubrication: wear-resistant bearings are used
12. Bearing cover: Separate the exposed surface of the bearing to prevent rubber samples from entering the bearing chamber and extend the service life of the bearing;
13. Material baffle: The width can be flexibly adjusted, and the amount of rubber material can meet the requirements Less adhesive material, adjust towards the middle, and more adhesive material can be adjusted towards both sides.
14. Material receiving basin: Made of stainless steel, easy to clean, pollution-free and rust free.
15. Mechanical structure: Steel plate (lighter weight, smaller volume, higher mechanical strength, and better toughness than traditional cast iron)
16. Volume: (W × D × H) 1200 × 550 × 1300mm
17. Power supply: 3 ∧, AC380V，15A
18. Weight: Approximately 620kg
Similar Product Recommend
