Magnescale digital display meter

NegotiableUpdate on 05/07

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

LT30-2GC Magnescale digital display meter $r $n equipped with 0.1 amp; amp; #181; The display resolution of m is equivalent to the highest resolution of the DK800S series of small high-precision contact digital length meters

Product Details

Magnescale digital display meterLT30-2G

Equipped with a display resolution of 0.1 μ m, it supports the minimum resolution of the DK800S series of small, high-precision digital instruments.

Minimum display resolution: 0.1 μ m
Origin detection function
The pass/fail judgment output for all models. The data can be output as BCD and RS-232C types.
Small size and light weight: DIN standard (W72mm × H72mm)
Comparator function
Reset/preset function
Alarm function, indicating fast response speed and poor connection of length measurement unit, etc.
Save set values
2-channel addition and subtraction (2CH type)

Magnescale数显表

Magnetic Scale LT30-2G Digital Display MeterTechnical parameters

Main specifications
1. I/O connector: Input: reset, peak hold start, peak hold pause, RS trigger (RS-232C model only)/Output: pass/fail determined (optocoupler) 2 BCD (36 pin half pitch connector): Input: reset, peak hold start, comparison value selection (4 models)/Output: 6-digit (open collector) Output: current value, maximum value, minimum value or P-P value according to selection, alarm output 3 RS-232C (8pin mini DIN connector): Reset, preset value setting and calling, peak hold start, peak hold pause, current value latch, software version reading, comparison value setting, current value, maximum, minimum, P-P measurement mode selection and output, key locking and release, BCD (36pin half pitch connector) Input: Reset, peak hold start, comparison value selection (4 types)/Output: 5-digit (open circuit collector) Select output based on current value, maximum value, minimum value or P-P value, alarm output 4 RS-TRG terminals: trigger input for RS-232C data output *When connecting 5 length measurement units The content is subject to change without prior notice.
type name		LT30-2G	LT30-2GB	LT30-2GC
display		6-digit, backlit LCD, mode display
Input/Output	Input length measurement unit	2 CH
	I/O connector * 1	○
	BCD*2	–	○	–
	RS-232C*3	–	–	○
	RS-TRG*4	–	–	○
Reset function		Reset key and external input (I/O connector)
Reset function		–	–	RS-232C command
Preset function		Set preset values using preset keys, call using reset keys
Preset function		–	–	Set and call using RS-232C commands
Comparator function		Determine whether the comparator value is set through the LED display and I/O connector output (optocoupler) from the keys on the front panel of the three-level comparator
Comparator function		–	Four comparison values can be set (key input) and switched to BCD terminal	Set up using RS-232C command
Peak holding function		Start measuring/pause input to stop updating through the start input of the maximum, minimum, and P-P value I/O connectors
Peak holding function		–	–	RS-232C can be set and started
Input resolution		0.0001 millimeters, 0.0005 millimeters, 0.001 millimeters, 0.005 millimeters, 0.01 millimeters are available for selection
display resolution		0.0001 millimeters, 0.0005 millimeters, 0.001 millimeters, 0.005 millimeters, 0.01 millimeters are available for selection
direction		switchable
Origin function		Is there a selection for use (when using, wait for the origin signal input while turning on the power)
Maximum response frequency		20 MHz (phase difference between phase A and phase B)
Harmony and difference function		The selection of A+B, A-B, B-A corresponds to the direction setting
alarm		Speed and disconnection (comparison output "H" (OFF) for all I/O connectors displayed on the LCD)
alarm		–	BCD alarm terminal "H" (OFF)	–
Save data		Resolution, direction, comparator value, preset value, each mode, etc
Save data		–	BCD polarity transmission rate, etc	–
Key locking function		Long press the number selection key to lock/unlock the key
temperature range		Usage: 0~40 ° C, Storage: -10~50 ° C
Power consumption * 5		8.5 W	9 W	8.5 W
quality		About 210 grams	About 270 grams	Approximately 230 grams
power supply		Power input connector (3-pin): DC9.0-26.4 V
Suitable for length measurement units		DK800S series, DK series

Magnescale digital display meterLT30-2GProduct dimensions:

Magnescale数显表

Magnescale LT30-2G digital display meterAccessories

LT30

output cable

DZ252	RS-232 output D-sub 9-pin female connector (for LT series and MG series)
DZ253A	RS-232C output Dsub25 pin male connector (for LT series and MG series)
DZ254	RS-232C output pre disconnect cable (for LT series and MG series)