Aoti CNC system host fault repair easily solved

If there is inconsistency, then we can repair it from the manufacturer, because each manufacturer has a different definition of the electrical part. If the electrical part is not asked, then consider whether the motor is overloaded. Motor overload can also cause the motor to heat up during operation. You can check whether the screw guide rail is stuck or damaged, and take you to understand the machine tool and lathe: wire cutting machine dynamic water adjustment method. The definition of the electrical part is different.
Aoti CNC system host fault repair easily solvedWhether the malfunction of your CNC system is no screen display, black screen display when powered on, screen flickering after power on, garbled characters after power on, system crash during operation, communication failure, host failure, or stuck progress bar, Changzhou Lingke Automation always provides professional and reliable services to safeguard enterprise production.
The meaning of the old error code is manual control box version E-12: wire breakage protection stop e-13: travel overtravel protection E-18 or E-14, E-15: UVW output short circuit protection E-16: When the 220V power line connection is poor or there is a power outage, all function input contacts default to normally open, only when a certain function needs to be activated.

Adapting to the production of multiple varieties, a brief discussion on the maintenance and repair of drilling parts: The processing methods of various drill bits are used to process one or several parts. A series of machine tools are arranged according to the process, and automatic loading and unloading devices and workpiece automatic conveying devices are set between the machine tools. A set of machine tools composed of such a set of machine tools is called an automatic cutting production line.
Aoti CNC system host fault repair easily solved
Reason for emergency stop alarm fault in CNC system
1. Electrical circuit issues: An open circuit in the emergency stop circuit, a damaged limit switch, or a damaged emergency stop button can all cause an emergency stop alarm. For example, if the emergency stop button is pressed but not turned, or if the limit switch is not flexible due to poor working environment (such as adhesion of small iron chips or erosion by cutting fluid), the contact cannot bounce back to its original state after being pressed.
2. System parameter setting error: Unreasonable or incorrect system parameter settings may cause system signals to not be input and output normally, or reset conditions to not be met, resulting in emergency stop faults.
3. Reset condition not met: The information required for system reset specified in the PLC does not meet the requirements, such as servo power supply, spindle drive not ready, etc.
4. External interference or malfunction: Unstable voltage may cause the driver or frequency converter to sound an alarm, leading to an emergency stop alarm in the system. In addition, spindle unit alarms or spindle driver errors may also cause the system to stop urgently.

Cutting counterclockwise from the left side of the gourd punch, the entire blank is divided into left and right parts according to the cutting route. As the material connecting the left and right sides of the blank becomes smaller, the right side of the blank gradually disengages from the fixture and cannot resist internal residual stress, causing deformation of the workpiece. If the workpiece is cut clockwise, it will stay on the left side of the blank, close to the clamping position.

If a gas sample with a constant substance concentration (i.e. a constant ratio of parts per million of the gas of interest compared to the gas balance) happens to increase pressure, then there will now be more light absorbing molecules (or light emissions) in the gas in the sample, even if the actual concentration (percentage or ppm or ppb) remains unchanged, it will be recorded as a higher concentration. This is why pressure regulation is so important for gas leak detectors: unstable sample gas pressure can lead to measurement errors. The use of filter units to eliminate wavelengths related to interfering gases is called positive filtering in the field of spectroscopy. You may think that this is filtering out all wavelengths that the instrument should not 'care' about. In order for forward filtering to be effective, the leak detector must filter out all wavelengths associated with all interfering substances. In some applications, this may require multiple "series" stacked filters, each filter filtering out wavelengths of different interfering gases. When there are multiple interfering "species" in the sample, this technique is not only cumbersome.
Aoti CNC system host fault repair easily solved
Maintenance method for emergency stop alarm fault of CNC system
1. Check the emergency stop button and circuit: Check if the emergency stop button is pressed but not turned. If the button is damaged or stuck, it needs to be replaced or repaired. Use a multimeter to check if the emergency stop circuit is open, check if the circuit connections are loose or broken, reconnect or replace damaged circuits.
2. Check the limit switch: Check whether the limit switches of each axis are damaged or have poor contact. If there are iron chips adhering to the limit switches or cutting fluid erosion, clean them and test their function. If necessary, replace the switches with new ones.
3. Check the power supply and driver: Check if the power supply voltage is stable and install voltage stabilizing equipment. Check if there are any alarm messages on the drive. If so, troubleshoot according to the alarm code, such as checking the power supply and parameter settings of the drive.
4. Check the PLC program and reset conditions: Check the relevant logic conditions through the PLC program to confirm whether the emergency stop was caused by a program error. Check whether the required information for system reset specified in the PLC is met, such as whether the servo power supply and spindle drive are ready.