AMCC device for artificial intraocular lens

GFR-20-IOL freezing device, suitable for DAC ALM lathe

This device only requires compressed air to operate and needs to be connected to its own

Air NetworkAccording to ISO standard dry air 3.2.2, the pressure is 7 to 8 bar.The air inlet and outlet will be set from the lower side of the spindle.

Please note that when the pressure is between 6 and 8 bars, the temperature on the clamp can reach -20 ° C,

When the temperature is below -36 ° CIt should be at a pressure of 9 bar. The gas consumption of this device is approximately per

100 to 135 liters per minute.The temperature adjustment needs to be manually set.

Turning freezer GFR-20-IOL

The refrigeration device is suitable for different models of lathes.

Used for DACSeriesIII lathes and OPTOFORM40/60/80 lathes.

Turning frozen chuck GFR-MF-20-IOL-qS

Standard and optional configurations: The standard tail maintains a length of 12.7 millimeters,

It can rotate in any direction,

There is a serial number,Has balancing functionYou can choose to add directional slots option.

GFF-20-IOLThe purpose and specifications of compact refrigeration units

This device is used for milling on traditional milling machines and requires compression of 6 to 9 bar for infusion

The air consumption is about 195 liters per minute. Under a pressure of 8 bar, the head clamp

The temperature above can reach -36 ° C.

Optional targeted sales options

The purpose and specifications of GFF-FF-20-IOL compact freeze-thaw table device

This device is only used for pre freezing/thawing. This device cannot be processed.

Compressed air at 6 to 9 bar, with a consumption of approximately 195 liters per minute

Optional targeted sales options

GFF-20-IOL Auto Compact Milling Freezing Device or Compact

Freezing thawing desktop device. The core shaft automatic clamping system is mainly used for automation.

Optional positioning pin.

Milling freezer GFF-20-OptoMill

Used for IOL machining on 0ptoMi11 milling machine.Can be used together with traditional ice clamps,

Turning from turning to milling can be done without disconnecting the IOL and ice chuck.

Single function operation.

GF-150-lol milling refrigeration device

Does not include blue container and gasket, only requires compressed air to operate,

The device will be simply connected. Go to your own air network

(According to ISO standard dry air, 3.2.2, pressure is 7 to 9 bar).

The air inlet and outlet are located on the rear side

GF-W-150 IOL gasket specific to freeze clamping Iols

Blue container and a set (lathe only) with 32 gaskets engraved with refractive power

Small milling refrigeration unit GF-50x50for Mill

Only compressed air is needed to work, and the device will be simpleConnect to its own air network (dry air 3.2.2. According to

ISO standard, pressure of 6 to 8 bar) air inlet and outlet will be set from the back.

Detachable freezer board GF-PLQ-50x50

Approximately 5 blanks can be placed

Milling machine turbine freezer GFT-M-K

Cold air (-12 ° C and 7 bar) must be set along the milling cutter.

Each GFT-Mi11 is dedicated to a specific type of milling machine.

(Used for hydrophilic or hydrophobic materials)

Lathe turbine freezer GFT-L

Install a cold air nozzle (-12 ° C and 7 bar) below the diamond tool,

It can cool the surface to be processed and transfer the chip to the vacuum system.

Turbine freeze milling combined lathe GFT-M-ALM

Cold air (-12 ° C and 7 bar) must be set along the milling cutter.

Each GFT Mill is dedicated to a specific type of mill spindle.

Milling turbine freezer head GFT-M – Nai (ind B)

Measurement of compressive force MFC-1385 Iol

The following standards: ISO 11979-3- Appendix A applies to hydrophilicity

Or hydrophobic material with high precision+/-0.01N (optional camera)

MFC-1385-Vision

Camera selection

Dynamic Fatigue Durability Tester MFD-24

Compliant with ISO 11979-3 Appendix 4.10

Suitable for hydrophilic or hydrophobic materials 51 Iol

Dynamic fatigue durability tester

MFD-3057- Simultaneously conducting 11 tests with multiple IoLs meets the requirements

Specification ISO 11979-3 Appendix 4.10 applies to hydrophilicity

Alternatively, hydrophobic materials can be selected: bath temperature regulation

GF-GF Flip System

It can be used in conjunction with GFR-20-Iols freezing chuck to

Ensure the flipping of IOLs and high positioning accuracy on both sides

The size is 416 * 356 * H435mm directional chuck option.

GF-GF hybrid flipping system for manual or integrated use with robots

This system can be used in conjunction with GFR-20-IOLs freezing chuck to

Ensure the flipping of IOLs and high positioning accuracy on both sides.

In addition, the system offers new directional clamp options.

Iols mechanical flipping device RRU-GF-GF

Mechanical IOL manufacturing system without pressure