Fully automatic asphalt mixture mixercomply withJTG E20-2011 <<Test code for asphalt and asphalt mixtures in highway engineering>>Standard requirements. Used for hot mixing various asphalt mixtures, as well as cold mixing various cement, lime and other mixtures, to replace manual stir frying operations. It is one of the equipment for developing test specimens in the laboratory of highway and urban road research, design and construction departments.

IIBH-20Structure of new asphalt mixture mixer
The asphalt mixture mixer adopts advanced heating device for heating, with high temperature control accuracy. The heating pot is made of three layers of material insulation processing, with good constant temperature effect. This machine is capable of automatic temperature control, timing, automatic mixing, lifting, and mixing of various particle sizes of mixtures without any jamming or crushing. It is easy to operate, master, time-saving, labor-saving, and safe and reliable.
3、 Intelligent mixture asphalt mixer|Main technical parameters of asphalt mixer:
1Mixing pot with maximum capacity:10L/20L
2Temperature control range:0-250℃Any setting
3Power supply:AC220V 50HZ
4Motor power:550W×2
5Heating power:2kW
6Rotation speed of the mixer:80r/min;Revolution speed:45r/min

Price of fully automatic intelligent asphalt mixture mixerInstallation instructions:

1The asphalt mixture mixer should be installed on a flat and sturdy cement concrete foundation, with a foundation thickness of not less than20Cm, tighten with expansion screws and level.
2Before use, power on and check all control buttons on the control panel; Rise, fall, stop; Is the time control and temperature control normal.
3The power supply is equipped with a main switch to turn off the power after work is completed or during maintenance and debugging. And the machine should have good grounding to prevent leakage.
5、 Operation steps of asphalt mixture mixer
1Firstly, preheat the mixer and mixture separately according to the standard requirements specified in the specifications, and then proceed with the work according to the standard procedures specified in the specifications.
2Connect220VPower supply, rotating power switch; Constant temperature setting: The temperature setting of the temperature controller is already set at the factory, and users generally do not need to adjust it to prevent changing the state and affecting use; Mixing time setting: Set the time controller switch to hour, minute, and second time periods. The time slot switch should be pre-set during use“minute”Section, the numeric dial below can be set to“0200”That means2minute. After setting the time, press the reset button.
3First, set the heating temperature, press the mixing switch, and then start the descent button to lower the mixing blades while stirring. When the mixing blades approach the bottom of the mixing pot, the descent stops and normal mixing begins. After the mixing time is up, the mixing automatically stops. Activate the up button to make the mixing system rise and automatically stop in place. When stirring for the second time, press the reset switch, then press the mixing button and the down button to start automatically.
4After discharging and lifting the mixing system into place, hold the heating pot flipping handle with one hand and remove the pin at the bearing to flip the heating pot. Use a spoon to scoop out the mixture and place it in a porcelain tray to prepare samples as needed.

Price of fully automatic intelligent asphalt mixture mixerCleaning and maintenance
1Cleaning: After the mixing of the mixture is completed and stopped, the power should be cut off first, and the heating pot, mixing blades, and other parts of the machine should be cleaned without leaving any asphalt residue or dirt.
2Maintenance: After cleaning, the machine can be maintained. Wear parts such as guide columns and lifting columns should be lubricated with appropriate mechanical oil. If not in use, a cover should be added to keep the machine clean.
7、 Intelligent mixture asphalt mixer|Precautions for using asphalt mixer
1Wear protective gloves during operation to prevent burns!
2When retrieving materials, the pin at the bearing should be removed, and caution should be taken when using the material tray to retrieve materials from the flipping pot to prevent skin burns caused by hot materials.
3First, set the heating temperature, press the mixing switch, and then start the descent button to lower the mixing blades while stirring. When the mixing blades approach the bottom of the mixing pot, the descent stops and normal mixing begins. After the mixing time is up, the mixing automatically stops. Activate the up button to make the mixing system rise and automatically stop in place. When stirring for the second time, press the reset switch, then press the mixing button and the down button to start automatically.
4After discharging and lifting the mixing system into place, hold the heating pot flipping handle with one hand and remove the pin at the bearing to flip the heating pot. Use a spoon to scoop out the mixture and place it in a porcelain tray to prepare samples as needed.