Product Categories

Shanghai Gaotian Pump Co., Ltd

E-mail
Phone
Address
No. 178 Linsheng Road, Industrial South Zone, Tinglin Town, Jinshan District, Shanghai

Contact Now

YG type oil pump

NegotiableUpdate on 02/24

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

Product Name: YG Type Oil Pump Model: YG80-160 Power 7.5KW Product Category: Oil Pump → YG Type Oil Pump Caliber Range: DN80-1000 Flow Range: 131-24000m3/h Head Range: 6.5-135m Our Advantages: In stock, special materials can be customized, product performance is stable, and service life is more than 5 years. Selection and quotation: You only need to provide the flow rate, head, and motor power of the water pump. If not available, we will calculate for you

Product Details

YG type oil pump

1、 Product Overview:

YG type oil pump is a combination of excellent domestic hydraulic models selected by our scientific and technological personnel in collaboration with domestic water pump experts. It adopts the performance parameters of IS type centrifugal pumps and is ingeniously designed on the basis of general vertical pumps. At the same time, suitable hot water, high-temperature corrosion-resistant chemical pumps, and oil pumps are derived from ISG type pumps according to different operating temperatures, media, etc. This series of products has the advantages of high efficiency, energy saving, low noise, and reliable performance, and meets the standard requirements of JB/T53058-93 of the Ministry of Machinery of China. The products are designed and manufactured according to the international ISO2858 standard.

2、 Usage and application areas:

YG oil pump is used forTransporting non corrosive, flammable, and explosive liquids. The temperature ranges from -20 to 120 degrees Celsius, suitable for industries such as petroleum, textiles, and machinery.

If you have any questions, you can call: 021-57239999 orClick to consult experts for selection and quotation

3、 Material and motor requirements for water pump:

The conventional material is HT250 gray cast iron, while the stainless steel materials are 201 stainless steel, SS304, 316, and 316L stainless steel.

Part name	Pump body, pump cover	impeller	axle
material	HT250,1Cr18Ni9Ti	HT250,1Cr18Ni9Ti	45 ,2Cr13

The motor is a Y2 series enclosed self fan air-cooled squirrel cage three-phase asynchronous motor, and the explosion-proof motor is a YB2 series.voltage：380V，phaseThree phase,Frequency: 50Hz (can be 60Hz, etc.),Installation location: indoor or outdoor, protection level: IP54, insulation level: F, installation type: V1.

4、 Advantages:

1. Significant reduction in land area: saving about 30-60% of infrastructure investment.

2. The motor and pump are coaxial: simplifying the intermediate connection structure, and the impeller has good dynamic and static balance, so it runs smoothly and reliably with low vibration and noise.

3. Easy installation: The import and export flanges are the same and on the same horizontal line.

4. No leakage: Adopting corrosion-resistant mechanical seals, there is no serious leakage problem caused by packing sealing, ensuring a clean and tidy operating site. The service life of mechanical seals is over 10000 hours.

5. Wide applicability: flow range from 1.5 to 2650m3/h, head from 7.5 to 150M, caliber from 40 to 500mm, divided into conventional flow type and expansion type; There are a total of 240 specifications for basic and cutting types.

If you have any questions, you can call: 021-57239999 orClick to consult experts for selection and quotation

5、 YG Details:

Motor diagram:

Details of impeller:

6、 User feedback:

7、 Model meaning:

YG100-250（I）A（B）

YG - Vertical Oil Pump

100-- Inlet and outlet diameter

250- nominal diameter of impeller

(I) Spread flow pattern (without this symbol indicating regular flow)

A (B) - The impeller undergoes the first (second) cutting

8、 YG pump type spectrum for you to choose from, making it easy for you to learn how to select

For example, when the flow rate of the water pump is 25m3/h and the head is 20 meters, we first find 25 (unit: m3/h) on the horizontal axis, and then find 20 on the vertical axis. The two lines converge to form a point, which is the model of this pump. The pump model is ISG65-125

If you have any questions, you can call: 021-57239999 orClick to consult experts for selection and quotation

9、 Structure diagram:

10、 Installation instructions

During installation, the weight of the pipeline should not be borne on the pump body, otherwise it may damage the water pump.

2. The pump and motor are integrated structures that have been calibrated by the manufacturer before leaving the factory, and do not require adjustment during installation, making installation very convenient.

3. The installation must tighten the anchor bolts, and the pump should be inspected at regular intervals to prevent loosening and avoid vibration during pump start-up, which may affect the performance of the pump.

4. In order to maintain convenience and ensure safe use, a regulating valve should be installed on the outlet pipeline of the pump and a pressure gauge should be installed near the pump outlet. For high lift pumps, to prevent water hammer, a check valve should also be installed in front of the pump outlet gate valve to cope with sudden power outages and other power loss accidents, ensuring that the pump operates under optimal conditions.

5. When the pump is used in situations with suction, it should be equipped with a bottom valve, and the inlet pipeline should not have too many bends. At the same time, there should be no air or water leakage to avoid affecting the suction capacity of the pump.

To prevent impurities from entering the pump and blocking the flow path, a filter should be installed before the pump inlet to improve performance.

7. The pump should be tested regularly (usually 15-20 days) for about 1 hour to prevent the shaft from getting stuck and unable to operate in emergency situations.

11、 Instructions for use:

Before startup:

1. The hood should be opened and manually turned to check for flexibility.

2. Open the inlet valve and exhaust valve to fill the pump chamber with water, and then close the exhaust valve.

3. Tap the motor to confirm if the steering is correct.

Run:

1. Fully open the inlet valve and close the outlet pipeline valve.

2. Connect the power supply, and when the pump speed reaches normal, open the outlet pipeline valve and adjust it to the desired operating point.

3. Observe whether there are any abnormal situations after the pump is running. If there are any abnormal situations, stop the pump immediately for inspection, handle them before running again.

Parking:

1. After gradually closing the outlet valve, cut off the power supply.

2. Close the inlet valve.

3. If the ambient temperature is below 0 ℃, measures should be taken to keep warm.

If you have any questions, you can call: 021-57239999 orClick to consult experts for selection and quotation

Fault causes and troubleshooting methods:

Fault phenomenon

Possible causes

Troubleshooting

Pump non suction outlet pressure gauge and vacuum gauge

The pointer is cracking and jumping violently

1Insufficient water filling in the pump

2Water leakage in the suction pipeline or sealing instrument

3The outlet valve opens too much when the pump starts

4Insufficient submergence depth of bottom valve

5The pump is not filled with water and there is air inside

6Air leakage in the inlet pipeline

7The installation of the inlet pipeline is incorrect, resulting in air blockage

8The outlet is blocked and the check valve cannot be opened

1Check if the bottom valve is leaking and refill with water

2Identify the leaking area and tighten it

3When starting, the outlet gate valve is closed. After the speed returns to normal, slowly open the outlet valve

4Adjust the submergence depth to1.5More than twice the diameter of the inlet pipe

5Check if the bottom valve is leaking and refill with water

6Seal the leaking area

7Reinstall the inlet pipeline

8Exhaust gas

Pump does not absorb water, vacuum gauge

Display high vacuum

1The bottom valve cannot be opened or is clogged

2Filter and suction pipe blockage

3High suction distance

1Correct and replace the bottom valve

2Disassemble and remove foreign objects

3Reduce suction distance

Pump does not produce water, pressure gauge

Displaying pressure

1The resistance of the water outlet pipe is high, and the check valve and other valves are not opened

2Motor reversal

3Impeller blockage

1Reduce pipe resistance and replace valves

3Remove foreign objects

The crew cannot start

1Not meeting the starting conditions

2Motor malfunction

1 Check if it meets the starting conditions

2 Check and repair the motor

Unable to achieve the designed traffic

And lift

1There is air inhalation

2The impeller, inlet and outlet pipelines, and filter are partially blocked

3The water level has decreased and the submergence depth is insufficient

1 Check for air intake and avoid it

2 Disassemble and remove foreign objects

3 Deepen the submergence depth

4 Check the power frequency

Mechanical seal leakage

1Crystallization phenomenon occurs when the medium contains particles or liquids

2Uneven installation of mechanical seals

3Mechanical seal dynamic and static ring surface without water dry grinding

4Normal wear and tear

1 Clean the pipeline to prevent crystallization

2 Reinstall and flatten

3 When starting the pump, exhaust the air inside the pump to prevent dry friction of the mechanical seal

4 Replace the machine seal

Bearing overheating

1Oil and grease loss inside the bearing

2Lubricating oil aging

3The bearing is faulty

1 Replenish lubricating oil

2 oil change

3 Check, repair or replace

Pump noise field and vibration

1There is air in the pump and pipeline that has not been expelled

2The water pump deviates from the design operating conditions during operation

3The water pump is operating at overload

4Bearing oil shortage or wear

5Poor pump and pipeline support

6Pump cavitation occurs

1 Eliminate air

2 Run near the design point

3 Adjust the valve to reduce load during operation

4 Replace bearings and replenish lubricating oil

5 Strengthen support and adopt vibration isolation measures

6 Improve inhalation conditions to avoid cavitation

Motor overcurrent

1The pump operates at an extremely high flow rate

2Mixing other foreign objects into the medium

3Voltage too low

4Bearing damage

5The rotation speed is too fast

1 Adjust the outlet valve

2 Remove foreign objects

3 Operate the pump at normal voltage

4 Replace bearings

5 Check the power frequency

motor burnout

1 Long term overload operation

2 The stator is damp

3 Motor phase loss operation

1 Adjust operating conditions

2 Improve the operating environment of the unit

3 Check and troubleshoot the power supply

If you have any questions, you can call: 021-57239999 orClick to consult experts for selection and quotation

13、 Performance parameters of ISG vertical centrifugal pump: