Product Categories

Jingjia Science and Trade (Kunshan) Co., Ltd

E-mail
jingjia17@sina.com
Phone
13656262369
Address
14-15, Building 3, Henglong Electromechanical City, 567 Xinnan Middle Road, Kunshan City, Jiangsu Province (opposite the New Bus Station on National Highway 312)

Contact Now

Wear Wheel

NegotiableUpdate on 07/22

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

Brief description: Based on the actual wear condition of the tested material, there are five types of abrasive particles for the wear wheel: Calbrase rubber and alumina abrasive particles for elastic wear; Calibrade ceramic, silicon carbide abrasive non elastic wheel; Wool wheel without abrasive particles; Rubber has no abrasive particles, unless used in conjunction with sandpaper for tungsten carbide thread cutting and tearing motion, used for elastic materials such as rubber, leather, or floor mats;

Product Details

Wear Wheel Selection Table:

model	number	type	component
CS-10	125320	elasticity	Rubber, abrasives
CS-10F	125321	elasticity	Rubber, abrasives
CS-17	125322	elasticity	Rubber, abrasives
H-10	125323	Inelastic	ceramics
H-18	125324	Inelastic	ceramics
H-22	125325	Inelastic	ceramics
H-38	125326	Inelastic	ceramics
CS-0 S-32	125344 125344	elasticity	Non abrasive rubber
S-42 S-33	125564 121124	elasticity	sand paper strip
CS-5	125319	elasticity	Wool blanket
S-35	125345	Inelastic	tungsten carbide
S-39	125529		leather

be careful:
Generally, Calibrade grinding wheels are used to test flexible samples, while Calibrase is used to test harder samples.

Other wear accessories:

200 type diamond
Calbrase grinding wheel dresser

Used for precise adjustment of Calibrade grinding wheels. To ensure the diameter size *, the grinding wheels are always adjusted in pairs.
The diamond cutting head is installed on an adjustable position gripper and placed on a shielded guide block, which can move tangentially due to the manual crank and feed thread. A vacuum cleaner is used to remove abrasive particles.

S-31	NEMA standard glass panel, 4 'square, aperture 1/4', thickness 1/8 'flat glass, 10 pieces.
S-32	NEMA grinding wheel (same as CS-0), one pair.
S-33	100 pieces of sanding paper with adhesive backing, adhered to the circumference of S-32 (CS-0), can be used as a Calibrase grinding wheel, complying with EN, ISO, DIN standards.
S-34	NEMA standard board, 0.032 ', zinc, 1/4' hole, 5 pieces.
S-36	50 sample gaskets, 4 1/4 'square, with pressure-sensitive adhesive used to adhere the samples. Flexible test samples are placed on top and pressed by grinding wheels. The gaskets are printed in the format of a record sheet.
S-36-1	50 circular sample gaskets
S-37	100 sample gaskets, 41/4 'square, with adhesive on both sides.
S-37-1	100 circular sample gaskets.
S-38	Standard gasket, 4 'square, 1/8' thick, 1/4 'hole, organic glass, 10 sheets, used for calibrating 155 type.
S-40	The 155 type sand can only be used after filtering through the American standard # 80 sieve first.
S-41	Container, capable of holding 50 pounds of # 240 alumina particles, for Type 155.
S-42	100 pieces of sandpaper strips with adhesive backing, adhered to the circumference of S-32 (CS-0), in compliance with NEMA testing standards.
503-0022	500g friction head, one pair
503-0023	1000g friction head, one pair
ST-11	A piece of grinding stone with a diameter of 4 ', a thickness of 1/2', and a hole diameter of 5/8 ', used for wheel shaped natural or synthetic rubber. The two ends of the grinding stone are rough on one side and smooth on the other, used for refreshing CS-10F
S-12	Brush for cleaning sample tray
S-16	Sample tray, 20 grams, steel, 4 'square, 1/4' hole, 10 pieces.
S-11	Sandpaper, grit 150, elastic wheel trimmed paper, diameter 4 ', 100 pieces.