TransfererTechnologiesRSS series torque sensor LCA-RTC red image industrial intelligence

TransfererTechnologiesRSS series torque sensor LCA-RTC red image industrial intelligence

Chixiang Intelligent Technology (Shanghai) Co., Ltd. is a one-stop service provider in the field of industrial control automation. As a domestic supplier of industrial spare parts, Red Elephant Industries, headquartered in Berlin, Germany, has a wide range of high-quality European brand supply channels. *The product supply chain covering the European Union, with a wide range of supply brands, low procurement prices, and short logistics cycles, are the three outstanding advantages of Red Elephant Industry.
At present, Chixiang has established long-term friendly cooperative relationships with hundreds of domestic factories, covering fields such as automobile manufacturing, metallurgy (steel mills), tobacco manufacturing (tobacco factories), hydraulic industry, power industry (power plants), petrochemicals, rail transit (high-speed rail, subway), textile industry, paper industry, engineering machinery manufacturing, etc.
Product Category Introduction:
RST Torque Sensor Series: The RST series is a low range rotary torque sensor with 11 full ranges ranging from 10 to 30K inch pounds. The sensing element adopts high-quality aluminum foil strain gauges, as well as silver slip rings and silver brushes for data transmission. In the dynamic characteristic box below, WR2、 The values of bending natural frequency and torsional stiffness are approximate, and the data in the table only involves torque acquisition and does not include the influence of couplings or other rotating masses, which are all part of the dynamic system.
Product model: RST-A10

RSS torque sensor series: The RSS series torque sensor has a range from 10 foot pounds to 250 foot pounds and can measure the wrench torque of bolts or nuts. These sensors are bidirectional and can measure the torque of tightening and breaking. The unrestricted rotation of the sensor shaft supported by ball bearings allows monitoring of the entire tightening cycle. The sensing element uses high-quality bonded foil strain gauges, as well as refined silver slip rings and two silver graphite brushes on each ring to transmit data.
Product model: RSS-250

RTS torque sensor series: The design of the RTS series torque sensor is to meet the needs of measuring torque below 62.5 inch pounds without sacrificing stiffness or sensitivity to forces in other directions. They are made of sensor quality aluminum and undergo anodizing treatment for long-term durability, and are equipped with high-quality aluminum foil strain gauges and materials to ensure high reliability. Four bolt hole modes, using O.D. or L.D. leads at both ends, can easily adapt to any application.
Product model: RTS-10

TRT torque sensor series: The TRT series reactive torque sensor has long-term reliability due to the use of non moving parts and adhesive foil strain gauges. Whenever possible, the method of torque measurement is through reactive torque sensing, eliminating the high maintenance and cost of slip rings, bearings, and brushes.
Product model: TRT-50
MLP Weighing Sensor Series: The MLP series weighing sensors are designed with economy as the primary consideration, and they are scaled down versions of our successful LPO series weighing sensors. MLP-10 to MLP300 are anodized aluminum. MLP-25SS, MLP-200SS, MLP-300sS, and MLP-500 to MLP-1K are made of 17-4ph heat-treated stainless steel. The low profile design of the MLP series provides excellent stability for stretching and/or compression in online applications, while also saving space.
Product model: MLP-10

TBS Weighing Sensor Series: The TBS series thin beam force sensor has been found to have different parameters in instruments, household appliances, process control, robots, and automobiles, making it particularly suitable for small load measurement. They are designed for measurement and many other high-capacity applications. A specially developed integrated strain gauge includes all balancing, compensating, and conductive components, and is attached to the crossbeam to provide excellent stability and reliability.
Product model: TBS-25

EBB weighing sensor series: The EBB series is an economical low capacity curved beam weighing sensor suitable for various industrial and OEM force measurement and weighing applications. It is made of aluminum alloy and comes in 1, 2, 5, and 10 kilograms.
Product Model: EBB-1

LSP weighing sensor series: The LSP series is a low capacity, low-cost, high-precision single point bending beam weighing unit. It is an ideal choice for OEM applications such as electronic scales and weighing machines. Single point design has strong resistance to eccentric loads and can be directly installed on the base and weighing platform of the scale. The LSP series has moisture-proof sealant.
Product model: LSP-1

ESP weighing sensor series: The ESP series is an economical and high-precision single point bending beam weighing sensor. It is an ideal choice for OEM applications such as electronic scales and weighing machines. The single point bending beam design has strong resistance to eccentric loads and can be directly installed on the base of weighing instruments and weighing platforms. The ESP series has moisture-proof sealant.
Product model: ESP-6

SPL Weighing Sensor Series: The SPL series single point weighing sensor simplifies scale design, packaging machinery, and other industrial weighing equipment. Their single point design eliminates the need for multiple weighing sensors and consolidation boxes, simplifying the design and reducing costs. All PL series weighing sensors adopt 10096 aluminum structure and have moisture-proof sealant, which also makes them suitable for humid environments.
Product model: SPL-65

SBL Weighing Sensor Series: The SBL series heavy-duty shear beam weighing sensor is an ideal choice for process weighing and low rise industrial scales. These economical weighing sensors are easy to install and also durable on site. Environmental protection is provided through water-resistant potting, compression sealing, and stress relief cable entry, as well as corrosion-resistant nickel plated steel.
Product model: SBL-500

SBO weighing sensor series: The SBO series weighing sensor can be used for tension or compression applications, for measuring weight and force. The SBOS series is made of anodized aluminum for 50 to 1000 pounds, and stainless steel for 2000 to 5000 pounds that has undergone 17-4ph heat treatment. The sensing element includes a high-quality adhesive foil strain gauge and is sealed to withstand most industrial environments.
Product model: SB0-50

DSM Weighing Sensor Series: The DSM series double screw installation weighing sensor has one screw at each end for easy online installation, ranging from 100 pounds to 10000 pounds. These weighing sensors are made of heat-treated 17-4ph stainless steel in height. The sensing element uses high-quality adhesive aluminum foil bandages and is sealed to protect it from most industrial environments.
Product model: DSM-100

SSM Weighing Sensor Series: The SSM series surface screw mounted weighing sensor is designed for surface mounting, applying loads through the installation of screws for tensile or compressive applications. The matching surface must be flat with a diameter of at least 2 inches. There are eight threaded mounting holes on the bottom surface for fixing from below. These sensors are made of heat-treated 17-4ph stainless steel, and the sensing elements include mass bonded foil strain gauges. They are sealed and can withstand most industrial environments.
Product Model: SSM-100

HFG Weighing Sensor Series: The HFG series is a pocket sized handheld high-quality digital load cell. Overall, this force gauge is a useful measuring instrument for your company, which can be used for handheld applications or hard installed through the four threaded holes on the back. Engineering units such as lb, oz, kg, N, or kN can be selected, with a load capacity of up to 110 pounds and a full-scale accuracy of 0.5% for tension or compression. The HFGs series can be used for continuous or peak measurement. The standard accessories include a test hook, extension rod, and compression plate, as shown in the following figure. Four replaceable AA batteries are available, and an AC power source can also be selected.
Product model: HFG-11

Brand model:
RST-A10、RSS-250、TRS-2K、SS-DLS、DPM-3、CLC-50K
TMO-2 Weighing Sensor Signal Regulator Series: The TMO sensor module is a complete differential amplifier/signal conditioner with a built-in power supply. This unit provides excitation, balance, and span adjustment (through a 10 turn pot), as well as shunt calibration required to connect the bridge sensor provided by the user to the indicator instrument, with a zero to full scale output of 4-20mA. TMO provides a floating shunt calibration circuit to apply calibration to the sensor, thereby eliminating errors caused by line losses.
Product models: TMO-2, TMO-2A

PSM Weighing Sensor Power Series: PSM is a power package that can be installed on the chassis. They are an ideal choice for withdrawing specialized microprocessor systems, instrument design, and testing equipment. PSM-F10 can also be used as a supplementary workbench or laboratory power supply. The special 'C-clip' type of blocking strip can fix wires without twisting. Please pay attention to the protected recessed isolation tape facing the top of the chassis. This allows for connections to be made in a narrow area while protecting the isolation tape from physical damage. No other product can provide this combination of durability, flexibility, and convenience.
Product models: PSM-R, PSM-F10

SLB Weighing Sensor Series: The SLB series ultra small weighing sensors (Load Buttons) are designed for compression applications with limited space. The matching surface must be flat to achieve the final result. The loading diameter is slightly raised to achieve load distribution. The sensor is made of 17-4ph stainless steel that has undergone heat treatment, and the sensing element uses a high-quality adhesive foil strain gauge. They are sealed to protect them from most industrial environments.
Product model: SLB-25

LBO Weighing Sensor Series: The LBO series (Load Button) weighing sensor is designed for compression applications with limited space. The matching surface must be flat and have a diameter of at least (D1). The load diameter (D2) is slightly raised to accurately distribute the load. There are threaded mounting holes on the bottom surface for easy fixation from below. These sensors are made of heat-treated 17-4ph stainless steel, with good sealing properties, and can be used in most industrial environments.
Product model: LB0-100

LBC Weighing Sensor Series: The LBC series (Load Button) weighing sensor is designed for compression applications with limited space. The matching surface must be flat and have a diameter of at least (D1), with a slightly raised load diameter (D2) for accurate load distribution. Provide mounting holes for fixing from the top. These sensors are made of heat-treated 17-4ph stainless steel, with good sealing properties, and can be used in most industrial environments.
Product model: LBC-100

LBM Weighing Sensor Series: The LBM series (Load Button) weighing sensor is designed for compression applications with limited space. This weighing button can directly replace many of the same types and bolt patterns currently used in the industry. The matching surface must be flat with a diameter of at least 2 inches. The loading diameter is slightly raised to accurately distribute the load. There are eight threaded mounting holes on the bottom for fixing from below. These sensors are made of heat-treated 17-4ph stainless steel, and the sensing elements are made of high-quality adhesive aluminum foil bandages. They are sealed and can withstand most industrial environments.
Product model: LBM-50

MLC Weighing Sensor Series: The MLC series is our miniature high-capacity compression type weighing sensor/force sensor, with a low profile and compact size, suitable for various portable and specialized applications, up to 30000 pounds. The low bias design gives it an ultra fast frequency response. MLC is designed to be installed on a shallow machined flat pocket or smooth surface, and can be freely installed or fixed through the 6-32 tapping holes at the bottom. These sensors are made of heat-treated 17-4 pH stainless steel, with sensing elements made of high-quality adhesive aluminum foil bandages and sealed to protect them from most industrial environments.
Product model: MLC-2K

CLC Weighing Sensor Series: The CLC series is a high-capacity compression type weighing sensor with a low profile and compact size, suitable for a wide range of portable and specialized applications. The load diameter (D1) is slightly raised to achieve load distribution. The low deflection design gives it an ultra fast frequency response. All series are made of 17-4ph heat-treated stainless steel and include a stainless steel molded connector system designed to resist rinsing and splashing. The matching connector is sold separately and comes in three different cable lengths.
Product model: CLC-50K

THA weighing sensor series: The outer diameter of the THA series through-hole weighing sensor is 1.00 inches, and there are two different through-hole diameters to choose from within each capacity range. These weighing sensors are made of heat-treated 17-4 pH stainless steel. The sensing element includes a high-quality adhesive foil strain gauge and is sealed to withstand most industrial environments.
Product Model: THA-50-P

THB Weighing Sensor Series: The THB series through-hole weighing sensor has an outer diameter of 1.50 inches, with up to four different through-hole diameters available for each capacity range. These weighing sensors are made of heat-treated 17-4 pH stainless steel. The sensing element includes a high-quality adhesive foil strain gauge and is sealed to withstand most industrial environments.
Product Model: THB-100-P

THC Weighing Sensor Series: The outer diameter of the THC series through-hole donut weighing sensor is 2.00 inches, with up to six different through-hole diameters available for each capacity range. These weighing sensors are made of heat-treated 17-4 stainless steel. The sensing element includes a high-quality adhesive foil strain gauge and is sealed to withstand most industrial environments.
Product Model: THC-250-P

THD Weighing Sensor Series: The THD series through-hole weighing sensor has an outer diameter of 3.00 inches and up to 9 different through-hole diameters to choose from within each capacity range. These weighing sensors are made of heat-treated 17-4 pH stainless steel. The sensing element includes a high-quality adhesive foil strain gauge and is sealed to withstand most industrial environments.
Product model: THD-2K-P

LWO Weighing Sensor Series: The LWO series is a gasket shaped weighing sensor based on stringage, commonly used for fastener testing and through-hole load applications. Our inventory range is compressed from 2400 to 300000 pounds, made of 17-4ph heat-treated stainless steel, and matched with bolt diameter and specific load characteristics. We welcome modifications to diameter, thickness, or load range for OEM applications. The sensing element adopts high-quality adhesive foil strain gauges and is sealed and protected for most industrial environments.
Product model: LW0-4