LCA-9PCTransducerTechniques Sensor Crimson Intelligent Technology

LCA-9PCTransducerTechniques Sensor Crimson Intelligent Technology

Brand Introduction:
An advanced sensor manufacturer in Germany, all sensor sensing elements use advanced metal foil strain gauge technology.

Brand detailed introduction:
Transducer Techniques was founded in 1979, designing and manufacturing complete weighing sensors, torque sensors, special-purpose sensors, and Rer ated instruments. Transducer Techniques' weighing sensors are specifically designed for weight and force measurement in diverse applications such as process control and factory automation. In many fields of science and industry, our load box also has other applications. The sensing element of the aluminum sensor includes bonded metal strain gauges wired in a full Wheatstone bridging configuration.
！

Product Features:
Torque of wrench for measuring bolts or nuts
Bi directional sensor
Unlimited spin control

Product Description: How to Translate
Our RSS series rotary socket wrench torque sensor ranges from 10 ft lbs to 250 ft lbs and can measure the wrench torque of bolts or nuts. These sensors are bidirectional and can measure the torque of tightening and breaking. The unrestricted rotation of the sensor shaft supported by ball bearings allows monitoring of the entire tightening cycle. The sensing element uses high-quality bonded foil strain gauges, as well as refined silver slip rings and two silver graphite brushes on each ring to transmit data.


Product Features:
Low range rotary torque sensor
Aluminum foil strain gauges

Product Description: How to Translate
The RST series is our low range rotary torque sensor, with 11 full ranges ranging from 10 to 30K inch pounds. The sensing element adopts high-quality aluminum foil strain gauges, as well as silver slip rings and silver brushes for data transmission. In the dynamic characteristic box below, the values of WR2 flexible natural frequency and torsional stiffness are approximate. The data in the table only involves torque acquisition and does not include the influence of couplings or other rotating masses, which are part of the dynamic system.


TMO-2 Weighing Sensor Signal Regulator Series: The TMO sensor module is a complete differential amplifier/signal conditioner with a built-in power supply. This unit provides excitation, balance, and span adjustment (through a 10 turn pot), as well as shunt calibration required to connect the bridge sensor provided by the user to the indicator instrument, with a zero to full scale output of 4-20mA. TMO provides a floating shunt calibration circuit to apply calibration to the sensor, thereby eliminating errors caused by line losses.
Product models: TMO-2, TMO-2A

PSM Weighing Sensor Power Series: PSM is a power package that can be installed on the chassis. They are an ideal choice for withdrawing specialized microprocessor systems, instrument design, and testing equipment. PSM-F10 can also be used as a supplementary workbench or laboratory power supply. The special 'C-clip' type of blocking strip can fix wires without twisting. Please pay attention to the protected recessed isolation tape facing the top of the chassis. This allows for connections to be made in a narrow area while protecting the isolation tape from physical damage. No other product can provide this combination of durability, flexibility, and convenience.
Product models: PSM-R, PSM-F10

SLB Weighing Sensor Series: The SLB series ultra small weighing sensors (Load Buttons) are designed for compression applications with limited space. The matching surface must be flat to achieve the final result. The loading diameter is slightly raised to achieve load distribution. The sensor is made of 17-4ph stainless steel that has undergone heat treatment, and the sensing element uses a high-quality adhesive foil strain gauge. They are sealed to protect them from most industrial environments.
Product model: SLB-25

LBO Weighing Sensor Series: The LBO series (Load Button) weighing sensor is designed for compression applications with limited space. The matching surface must be flat and have a diameter of at least (D1). The load diameter (D2) is slightly raised to accurately distribute the load. There are threaded mounting holes on the bottom surface for easy fixation from below. These sensors are made of heat-treated 17-4ph stainless steel, with good sealing properties, and can be used in most industrial environments.
Product model: LB0-100

LBC Weighing Sensor Series: The LBC series (Load Button) weighing sensor is designed for compression applications with limited space. The matching surface must be flat and have a diameter of at least (D1), with a slightly raised load diameter (D2) for accurate load distribution. Provide mounting holes for fixing from the top. These sensors are made of heat-treated 17-4ph stainless steel, with good sealing properties, and can be used in most industrial environments.
Product model: LBC-100

LBM Weighing Sensor Series: The LBM series (Load Button) weighing sensor is designed for compression applications with limited space. This weighing button can directly replace many of the same types and bolt patterns currently used in the industry. The matching surface must be flat with a diameter of at least 2 inches. The loading diameter is slightly raised to accurately distribute the load. There are eight threaded mounting holes on the bottom for fixing from below. These sensors are made of heat-treated 17-4ph stainless steel, and the sensing elements are made of high-quality adhesive aluminum foil bandages. They are sealed and can withstand most industrial environments.
Product model: LBM-50

MLC Weighing Sensor Series: The MLC series is our miniature high-capacity compression type weighing sensor/force sensor, with a low profile and compact size, suitable for various portable and specialized applications, up to 30000 pounds. The low bias design gives it an ultra fast frequency response. MLC is designed to be installed on a shallow machined flat pocket or smooth surface, and can be freely installed or fixed through the 6-32 tapping holes at the bottom. These sensors are made of heat-treated 17-4 pH stainless steel, with sensing elements made of high-quality adhesive aluminum foil bandages and sealed to protect them from most industrial environments.
Product model: MLC-2K

CLC Weighing Sensor Series: The CLC series is a high-capacity compression type weighing sensor with a low profile and compact size, suitable for a wide range of portable and specialized applications. The load diameter (D1) is slightly raised to achieve load distribution. The low deflection design gives it an ultra fast frequency response. All series are made of 17-4ph heat-treated stainless steel and include a stainless steel molded connector system designed to resist rinsing and splashing. The matching connector is sold separately and comes in three different cable lengths.
Product model: CLC-50K

THA weighing sensor series: The outer diameter of the THA series through-hole weighing sensor is 1.00 inches, and there are two different through-hole diameters to choose from within each capacity range. These weighing sensors are made of heat-treated 17-4 pH stainless steel. The sensing element includes a high-quality adhesive foil strain gauge and is sealed to withstand most industrial environments.
Product Model: THA-50-P

THB Weighing Sensor Series: The THB series through-hole weighing sensor has an outer diameter of 1.50 inches, with up to four different through-hole diameters available for each capacity range. These weighing sensors are made of heat-treated 17-4 pH stainless steel. The sensing element includes a high-quality adhesive foil strain gauge and is sealed to withstand most industrial environments.
Product Model: THB-100-P

THC Weighing Sensor Series: The outer diameter of the THC series through-hole donut weighing sensor is 2.00 inches, with up to six different through-hole diameters available for each capacity range. These weighing sensors are made of heat-treated 17-4 stainless steel. The sensing element includes a high-quality adhesive foil strain gauge and is sealed to withstand most industrial environments.
Product Model: THC-250-P

THD Weighing Sensor Series: The THD series through-hole weighing sensor has an outer diameter of 3.00 inches and up to 9 different through-hole diameters to choose from within each capacity range. These weighing sensors are made of heat-treated 17-4 pH stainless steel. The sensing element includes a high-quality adhesive foil strain gauge and is sealed to withstand most industrial environments.
Product model: THD-2K-P

LWO Weighing Sensor Series: The LWO series is a gasket shaped weighing sensor based on stringage, commonly used for fastener testing and through-hole load applications. Our inventory range is compressed from 2400 to 300000 pounds, made of 17-4ph heat-treated stainless steel, and matched with bolt diameter and specific load characteristics. We welcome modifications to diameter, thickness, or load range for OEM applications. The sensing element adopts high-quality adhesive foil strain gauges and is sealed and protected for most industrial environments.
Product model: LW0-4


Product Features:
Applicable to the head module on 04090-A

Product Description: How to Translate
The head module installed on 04090-A is delivered together with the corresponding base plate and 16mm and 19mm adapters.

Product Features:
Suction head adapter for 09390-A (used with clip module):
Adapter for non curved suction heads
Adapter for arm tips with connectors
Adapter for top connection

Product Description: How to Translate
The clip module should be installed on 04090-A and delivered with a standard adapter and corresponding base plate.

Technical Specifications:
There are specific adapters according to different connection methods
Product Features:
Power requirement: 12 to 26 volts DC
Sensitivity of the bridge: 0.5 mV/V to 10 mV/V
L Button diversion calibration network
Two pole low-pass optional filter from 100 Hz to 30 kHz

Product Description: How to Translate
The LCA-9PC module provides low-cost dedicated signal conditioning for single bridge weighing sensors or torque sensors. The ModeCA-9PC is equipped with DB9 male and female connectors, which need to be soldered onto the matching female or male wire connectors provided by the user. The device can be operated with a 4-wire connection next to the sensor, or with a 6-wire connection within a distance of 1 kilometer (3300 feet). An onboard 87.325kO resistor allows for easy shunt calibration upon pressing a button. The power requirement is 11.8 to 26 volts DC and the load current is 10 to 60 milliamps, the latter being suitable for providing 10 volts DC to a 350 ohm load for this device.


Product Features:
Power requirement: 12 to 26 volts DC
Sensitivity of the bridge: 0.5 mV/V to 10 mV/V
L Button diversion calibration network
Two pole low-pass optional filter 100 Hz to 30 kHz analog output 0 to+5V 0 to 10V. 0-16 mA, 0-20 mA or 4-20 mA

Product Description: How to Translate
The LCA-RTC module provides low-cost dedicated signal conditioning for single bridge weighing sensors or torque sensors. The LCA-RTC module comes with a detachable screw terminal connector that can accept wires without soldering. The jumper selection on the board includes sensitivity from 0.5 mW/y to 10 mV/V, and from 100 Hz to 30 Hz