-
E-mail
deyixm@163.com
-
Phone
13860482272，15980811072
-
Address
No. 7 Jinchang Road, Huli District, Xiamen
Product Categories
Xiamen Deyi Equipment Co., Ltd
IP5 6-pack sand and dust test box
NegotiableUpdate on 07/21
- Model
- Nature of the Manufacturer
- Producers
- Product Category
- Place of Origin
Overview
Brief introduction: According to the standard requirements, the IP5 6 box type sand and dust test box uses artificial simulated dust environment to test the dust prevention ability of the test sample. The specific requirements and qualification criteria should be in accordance with GB4208-93 (IEC60529-2001) or product standard requirements
Product Details
Details introduction:
IP56-pack sand and dust test chamberProduct Introduction
The sand and dust test chamber is suitable for testing the sealing performance of product shells, mainly used for testing the IP5X and IP6X levels specified in the shell protection level standards. Mainly simulating the damage caused by sandstorm weather to locks, automotive and motorcycle components, seals, power instruments and other products. By conducting experiments and adding protective nets or sand and dust measures to the installation and operation of general equipment, we aim to improve the product's ability to resist and protect against sand and dust.IP5 6-pack sand and dust test boxProduct advantages:The structure and working principle of this sand and dust test chamber are the same as GB4208-93 (IEC60529-2001), and an airflow heating device is added for use in environments with low temperatures or high humidity When the system is working, first put the dried standard talc powder into the sand and dust box at a rate of 2kg/M3, then put in the test sample, and then start the fan to form a high-density dust mist in the working chamber until the set operating time (usually 8h) is reachedThis device
It can effectively help users evaluate the anti sand and dust ability of samples, resist the influence of dust that may block openings, infiltrate cracks, gaps, bearings, and joints, and not reduce performance, efficiency, reliability, and maintainability due to the wear or blockage of sharp edged large sand particles. The sand and dust test chamber is suitable for conducting sand and dust resistance tests on various automotive components, including car lights, instruments, electrical dust covers, steering systems, door locks, etc.IP5 6-pack sand and dust test boxMeet the standards:
The sand and dust box is designed and manufactured in accordance with GB4208-93 (equivalent to IEC60529-2001) "Degrees of Protection Provided by Enclosures (IP Code)", and is suitable for conducting sand and dust tests on electrical products with characteristic numbers 5 and 6 (IPX5 and IPX6) This test chamber can provide non laminar vertical circulation airflow for dust, which can be timed and controlled; At the same time, a vacuum pump can be configured to extract air from the outer shell of the tested product, and the amount of extraction and pressure difference can be adjusted; In addition, an airflow temperature control device is installed inside the box to ensure that the test is conducted under standard environmental conditions According to the standard requirements, this test chamber uses artificial simulation of dust environment to test the dustproof ability of the test sample. The specific requirements and qualification criteria should be in accordance with GB4208-93 (IEC60529-2001) or product standard requirementsIP5 6-pack sand and dust test box
The sand and dust test chamber is suitable for testing the sealing performance of product shells, mainly used for testing the IP5X and IP6X levels specified in the shell protection level standards. Mainly simulating the damage caused by sandstorm weather to locks, automotive and motorcycle components, seals, power instruments and other products. By conducting experiments and adding protective nets or sand and dust measures to the installation and operation of general equipment, we aim to improve the product's ability to resist and protect against sand and dust.IP5 6-pack sand and dust test boxProduct advantages:The structure and working principle of this sand and dust test chamber are the same as GB4208-93 (IEC60529-2001), and an airflow heating device is added for use in environments with low temperatures or high humidity When the system is working, first put the dried standard talc powder into the sand and dust box at a rate of 2kg/M3, then put in the test sample, and then start the fan to form a high-density dust mist in the working chamber until the set operating time (usually 8h) is reachedThis device
It can effectively help users evaluate the anti sand and dust ability of samples, resist the influence of dust that may block openings, infiltrate cracks, gaps, bearings, and joints, and not reduce performance, efficiency, reliability, and maintainability due to the wear or blockage of sharp edged large sand particles. The sand and dust test chamber is suitable for conducting sand and dust resistance tests on various automotive components, including car lights, instruments, electrical dust covers, steering systems, door locks, etc.IP5 6-pack sand and dust test boxMeet the standards:
The sand and dust box is designed and manufactured in accordance with GB4208-93 (equivalent to IEC60529-2001) "Degrees of Protection Provided by Enclosures (IP Code)", and is suitable for conducting sand and dust tests on electrical products with characteristic numbers 5 and 6 (IPX5 and IPX6) This test chamber can provide non laminar vertical circulation airflow for dust, which can be timed and controlled; At the same time, a vacuum pump can be configured to extract air from the outer shell of the tested product, and the amount of extraction and pressure difference can be adjusted; In addition, an airflow temperature control device is installed inside the box to ensure that the test is conducted under standard environmental conditions According to the standard requirements, this test chamber uses artificial simulation of dust environment to test the dustproof ability of the test sample. The specific requirements and qualification criteria should be in accordance with GB4208-93 (IEC60529-2001) or product standard requirementsIP5 6-pack sand and dust test box
Product AlbumIP5 6-pack sand and dust test boxSelect key points
：
Inner liner material: Imported SUS stainless steel light plate.
Box shell material: Imported SUS stainless steel plate.
Visible glass door for easy observation of the condition of the tested sample inside the test chamber.
The bottom of the test chamber adopts high-quality fixed PU movable wheels.
There is a dust replacement device at the bottom of the test chamberIP5 6-pack sand and dust test boxParameter specifications
|
： |
Common models |
Studio Size |
|
|
Carton size |
DSC-500 |
800*800*800 |
|
|
1030*920*1660 |
DSC-800 |
800*1000*1000 |
|
|
1030*1120*1860 |
DSC-010 |
1000*1000*1000 |
|
|
1230*1120*1860 |
DSC-015 |
1000*1500*1000 |
|
|
1230*1620*1860 |
|||
|
Stainless steel material |
DSC-500A |
800*800*800 |
|
|
1030*920*1660 |
DSC-010A |
1000*1000*1000 |
|
|
1230*1120*1860 |
|||
|
Stainless steel material (adjustable wind speed) |
DSC-500B |
800*800*800 |
|
|
1030*920*1660 |
DSC-010B |
1000*1000*1000 |
|
|
1230*1120*1860 |
Power (kw) |
||
|
7KW |
Performance characteristics |
Net nominal wire diameter |
|
|
50um |
Nominal spacing between lines |
||
|
75um |
Dosage of talc powder |
||
|
2kg/m33 |
Airflow velocity |
||
|
Not exceeding 2m/s |
Dust concentration |
||
|
2Kg/m3 |
Fan cycle time |
||
|
0～99H59M |
Test piece power socket |
||
|
Dust proof socket AC220V 16A |
interconnected system |
controller |
|
|
PLC programmable controller |
vacuum system |
||
|
Equipped with pressure gauge, air filter, pressure regulating triple piece, connecting pipe (vacuum pump separately) |
circulating fan |
||
|
Enclosed alloy low-noise motor Multi blade centrifugal fan |
Dust heating system |
||
|
Stainless steel mica heating sleeve |
**Protection |
||
|
Leakage, short circuit, overheating, motor overheating, overcurrent protection |
Power supply |
||
AC220 V50HzIP5 6-pack sand and dust test box
Usage1
If the technical conditions of the sample require it, sample pretreatment should be carried out according to the requirements to keep the sample dry. The dustproof test is a part of the shell protection test, which is usually connected to the waterproof test. After the sample waterproof test, it must be dried before being placed in the dustproof box. If the pre-treatment conditions of the sample are not specified, it should be placed in the following normal atmospheric conditions for more than 2 hours according to GB2423.37:
A temperature: between 15 ℃ and 35 ℃;
B relative temperature: 45% -75%;
Atmospheric pressure: 8KPa-106Kpa.2
Place the pre processed unpackaged sample into the working space of the dust-proof box testing equipment. Unless otherwise specified for the test sample, the sample will not work without power during the testing process. The volume of the sample shall not exceed one-third of the effective working space of the testing equipment, and the distance between various samples and their dust-proof equipment shall not be less than 100MM3
Installation of samples with different levels of vacuum protection:
The protection level of A is 1P5X. For the type of sample (Class A) where the pressure inside the shell is lower than the surrounding atmospheric pressure during normal use, a suction hole should be set in the position close to the easily replaceable component, and a hose should be used to connect the suction port on the sample to the suction port of the vacuum system.
The B protection level is 1P5X, and the outer shell of the type of specimen (Class B) with a lower pressure inside the shell than the surrounding atmospheric pressure during normal use. If the product standard specifies a Class B shell, the tested product will not be vacuumed during the 1P5X test. If the product standard does not specify it, the tested product will be considered a Class A shell and must be vacuumed during the 1P5X test. Place the sample in the required position according to the technical specifications of the sample.
Samples with a protection level of 1P6X, whether they are Class A or Class B samples, must have their shells evacuated.IP5 6-pack sand and dust test box
Working environment conditions
1. Avoid environments with high humidity, direct sunlight, and dust.
2. A space of 80 centimeters should be left around, and it should not be tightly attached to walls or other testing equipment.
3. For the stability of the equipment, the ambient temperature and humidity should be maintained at a temperature of 5 ℃ to 30 ℃ and a humidity of ≤ 85% R.H.
4. To avoid uneven unevenness, it should be installed on a horizontal ground.
5. The installation site should have good ventilation and be easy to operate around.IP5 6-pack sand and dust test boxdailymaintenance
precautions
1. Replacement of talc powder: * * Add talc powder and replace after 20 experiments First, open the right side panel (bottom) of the dust box to see the fan turbine box. Open the manual locking door of the turbine box, use a brush to sweep out the talcum powder, and lightly tap the sand and dust box. There will be residual talcum powder flowing down the box wall. After cleaning, lock the door tightly
2. To prevent the talc powder from getting damp in the dust-proof box: it can be heated and run for 1 hour before the test. However, it should be noted that the heating temperature should not exceed 60 ℃. After heating, wait for the temperature inside the box to return to room temperature before testing
3. After the test inside the door, there may be residual talcum powder, which should be promptly cleaned with a brushXiamen Deyi Company's main products: high and low temperature alternating humidity test chamberHigh and low temperature damp heat test chamberHigh and low temperature alternating test chamber, high and low temperature test chamber, high and low temperature impact test chamberHumidity Chamber
Similar Product Recommend
