Horiba conductivity meter conductivity meter HE-200C ESH-001

NegotiableUpdate on 05/06

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

Horiba conductivity meter HE-200C ESH-001 is used to measure the conductivity and temperature of water samples. $r $n $r $n outdoor on-site installation, different from the panel installation of HE480C. According to USP lt;645 The quality guide is applicable for monitoring the recovery control of pure water/boiler drainage and online measurement of pharmaceutical water conductivity.

Product Details

On site installation type conductivity meterHE-200C ESH-01-C-S-ST-Y

Four wire transmission, low concentration

Horiba conductivity meter conductivity meter HE-200C ESH-001Measure the conductivity and temperature in the water sample.

Outdoor on-site installation, different from panel installation of HE480C. According to the USP<645>quality guidelines, it is suitable for monitoring the recovery control of pure water/boiler drainage and online measurement of pharmaceutical water conductivity.

range

Conductivity: 0-2000 μ s/cm, 0-200.0 ms/cm
(TDS 0 ~ 2000 mg/L)
Temperature: 0~100 ℃

sturdy

Dealing with harsh conditions during on-site measurement.
Operating temperature range (transmitter): -20~55 ℃
Rated power supply voltage: AC 100~240 V ± 10% 50/60 Hz
Aluminum alloy watch box: protection level IP65
Compliant with CE marking and FCC rules, suitable for use on overseas sites.

Horiba conductivity meter HE-200C ESH-001 best-selling model;

host:HE-200C

Split electrode:ESH-001-C-S-ST-Y、ESH-01-C-S-ST-Y

Integrated electrode:ESH-001-L-S-ST-Y-10、

Flow pool:EFA-30、EFA-30-P、

Split cable:CK-10M

intelligence

Convenient function to display liquid temperature simultaneously (transmission output available).
Respond to various types of temperature compensation.
The self diagnostic function can immediately detect sensor errors.
Environmentally friendly (lead-free) design that can handle WEEE and RoHS.
Rich interfaces (2-channel transmission output, compatible with RS-485, 3-contact output).

easy to maintain

Easy to view large display screen.
Easy to operate.
Can store calibration records.
Use thread terminals in the wiring board that will not come off for wiring

parameter

measurement method	Dual electrode communication method
range (Conductivity measurement and TDS conversion cannot be selected simultaneously) *Range only applicable to hygiene grade sensors (FS-01 series)	Electrode constant	/cm	0.01	0.1	1
	conductivity	uS/cm	0.000~2.000 0.00~20.00	0.000~2.000 0.00~20.00 0.0~200.0 0~2000*	0.0~200.0 0~2000
		mS/cm	0.0000~0.2000 0.000~2.000	0.0000~0.2000 0.000~2.000 0.00~20.00 0~200.0*	0.00~20.00 0.0~200.0
	TDS conversion	mg/L	0.00~2.00 0.0~20.0	0.0~20.0 0~200	0~200 0~2000
	temperature	℃	0~100 resolution: 0.01 ℃
repetitiveness	Conductivity: ≤± 0.5% F.S. TDS conversion: ≤± 1.5% F.S Temperature: ± 0.1 ℃ (or equivalent input)
linear	Conductivity: ≤± 0.5% F.S. TDS conversion: ≤± 1.5% F.S Temperature: ± 0.5 ℃ (or equivalent input)
Transfer output	2-4 mA DC input/output insulation type maximum load impedance 900 Ω Output range 1: Conductivity: arbitrarily set within the measurement range Output range 2: Temperature: can be set arbitrarily within the range of -10-160 ℃ Abnormal output: Fault state (3.8mA or 21mA) Keep function: can be set to: current value hold, any value hold
Contact output	3-point no voltage contact output relay contact SPDT (1c) Contact function: R1, R2: upper limit alarm, lower limit alarm, USP judgment, output signal retention optional FAIL: Fault alarm Output content: conductivity (or TDS conversion value), temperature
Contact input	one o'clock Contact form: collector open circuit, no voltage, contact a Contact function: external input for transmission output holding
communication function	RS-485 2-wire type, input/output insulation type (transmission output is non insulated)
temperature compensation	Range: 0~100 ℃ (extended and calculated for temperatures below 0 ℃ and above 100 ℃)
ambient temperature	-20~55℃
Temperature compensation component	Pt1000（0℃）
Correction function	Conductivity: Correction coefficient for input electrode constant (parameter input) TDS conversion value: based on specified coefficients (0.30-1.00) conversion Temperature: 1-point calibration compared to the reference thermometer
Self-diagnostic function	Sensor diagnostic error, transmitter malfunction
power supply	100~240 V AC 50/60 Hz Power consumption: 15 W or lower
construction	Outdoor installation type: IP65 protection level Installation method: 50A column or wall installation Shell material: Aluminum alloy Installation fixing and protective cover material: SUS304
weight	About 4.5 kg
Electrical certification	CE marking，FCC rules
Applicable electrodes	ESH and FS series conductivity sensors (electrode constants of 0.01/cm, 0.1/cm, 1.0/cm)

Electrode selection ESHSplit style