System features:

Reference 600+is a high-performance and research grade electrochemical testing system with fast scanning and low current characteristics, applied in physical electrochemistry (microelectrodes), fast cyclic voltammetry, electrochemical corrosion, electrochemical noise measurement, coatings and coatings, as well as sensor research.

Reference 600+has various auxiliary inputs and outputs to achieve auxiliary control functions, such as controlling rotating disk electrode devices. Temperature control can also be achieved through thermocouple interfaces.

Electrochemical impedance spectroscopy

Reference 600+can achieve accurate measurement of electrochemical impedance spectroscopy. The accurate spectrum of the measured impedance spectrum is shown below, which can determine the measurement error of the actual system. The spectrum is produced through actual measurements including real wires.

option

• Extend the length of the wire

  • The length of the wire (1.5 meters, 3 meters, 10 meters) is available for selection

    Provide more performance for Interface 600+. Each bullet point represents a performance.

    • Physical electrochemistry-Cyclic voltammetry, linear sweep voltammetry, chronoamperometry, chronopotentiometry, chronocoulometry, multi-step chronoamperometry, and multi-step chronopotentiometry techniques.
    • Pulsed voltammetryDifferential pulse voltammetry, conventional pulse voltammetry, reverse pulse voltammetry, Osteryoung square wave voltammetry and related techniques such as anodic stripping voltammetry.
    • DC corrosion-Conduct standard DC corrosion tests, such as polarization resistance, potential, cyclic polarization, and galvanic corrosion
    • Electrochemical energy devices-Test individual cells and stacks of batteries, capacitors, and fuel cells. Typical testing techniques include charging, discharging, cyclic charging and discharging, constant potential, constant current, self discharge, leakage rate, and read potential.
    • Electrochemical signal analyzer-Software for collecting and analyzing electrochemical noise signals related to time. Continuous monitoring of voltage and current at rates ranging from 0.1 Hz to 1 kHz. Fully functional analysis tools, such as statistical analysis, trend analysis, impedance spectroscopy, and histogram analysis.
    • Electrochemical frequency modulation-A non-destructive method for measuring corrosion rate. Through this technology, the corrosion rate is directly measured without the Tafel constant. In addition, this technology can determine the Tafel constant and provide parameters related to pitting corrosion.
    • critical pitting temperature-Control Gamry constant potential, TDC4 temperature controller, and related accessories to automatically measure the critical pitting temperature of materials.
    • electrochemical noise-Electrochemical noise testing is a more common technique. It is a software package compatible with ECM8 multiplexer for electrochemical noise measurement.
    • Electrochemical impedance-In addition to single frequency Mott Schottky measurements, it also includes constant potential, constant current, and mixed impedance measurements. This includes unique multi wave weighting techniques to improve signal-to-noise ratio. In terms of analysis, equivalent circuit diagrams are used to fit the data, Kramers Kronig conversion evaluation data and graphic editor, etc. The software includes an impedance simulation section.
    • eChemACTool kit - software tool kit for fully controlling the constant potential meter for impedance (EIS) measurement and EFM experiments.

    Other details

    • Measurement of electrodes 2, 3, and 4
    • Electrical isolation
      
      • Floating ground: used for high-pressure vessels, mechanical stress equipment, or pipelines.
    • portable
      
      • The size of a chemistry textbook weighs only 3 kilograms. Connect USB 2.0 to a Windows computer.

    • Built in EIS

      • Advanced DDS is used for EIS measurement from 10 μ Hz to 1 MHz.
    • DSP (Digital Signal Processing) mode
      • Oversampling mode improves signal-to-noise ratio and precise capacitance measurement.
    • Oversampling mode improves signal-to-noise ratio and precise capacitance measurement.
      
      • Gamry potentiostat and its control software adopt linear regression method to accurately measure and achieve IR compensation.
    • Auxiliary I/O
      

      • Through I/O design, control third-party devices: achieve external signal input, analog voltage output, analog current output, auxiliary A/D input, and digital I/O connectors.

    • Value retention period
      

      • 2-year manufacturer warranty service.

        system
        Potentiostat	correct
        galvanostat	correct
        Zero resistance current meter	correct
        Floating design (insulated from the ground)	correct
        electrode connection	2, 3, 4 or 5 electrodes
        Maximum current	±600 mA
        Current range	11 (60 pA - 600 mA)
        Current range (including internal gain)	13
        Minimum current resolution	20 aA
        Maximum applied potential	±11 V
        rise time	<250 ns
        Minimum time base	3.333 μs
        Noise and Ripple (Typical)	<2 μVrms
        weight	3 kilograms
        size	9 (W) x 19 (H) x 27 (D) 27 centimeters
        control amplifier
        cell voltage	±22 V
        Maximum current	>±600 mA
        speed setting	5
        EIS measurement
        Frequency range	10 μHz - 5 MHz
        EIS Accuracy	See Accuracy Contour Plot
        Apply voltage amplitude	3 V maximum
        Apply current amplitude	600 mA maximum
        Potentiometer
        Input impedance	>1014Ω || <0.2 pF
        Input Current	<10 pA
        bandwidth	>15 MHz at -3 dB
        CMRR	65 dB (1 MHz)
        potential
        Apply precision	±1 mV ±0.2% of setting
        Apply resolution	200 μV, 50 μV, 12.5 μV/bit
        measurement accuracy	±1 mV ±0.2% of reading
        measurement resolution	1 μV, 10 μV, 100 μV, 400 μV/bit
        electric current
        Application/measurement accuracy	±10 pA ± 0.05% of range ±0.2% of value (600 mA - 6 nA) or 0.75% of value (600 pA) or 1.5% of value (60 pA)
        Apply/measure resolution	0.003% full-scale/bit
        bandwidth	>10 MHz (600 mA – 600 μA) >0.15 MHz (6 μA)