Electric hydraulic demoulder manufacturer*

Electric hydraulic demoulder manufacturer*Usage:

1. Before use, first add 8L of hydraulic oil to the fuel tank (open the rear cover plate and add it)

Oil), check whether various oil pipe joints and fasteners are moving. If they are loose, tighten them to prevent oil leakage and affect use. Check the grounding of the electrical system.

2. Operating procedures and demolding methods:

At the beginning, move the manual lever to the middle stop position, and then press the start button on the panel

Button, power on, oil pump starts working; Move the manual rod to raise the piston a certain distance and observe for any abnormal phenomena such as jamming. If there are any, stop the machine to check and eliminate them. If there are no abnormal phenomena, raise the piston a certain distance and then lower it. Repeat this process several times to exhaust the air in the oil cylinder and observe that there are no bubbles in the oil pipe before normal use.

When demolding, attention should be paid to the accuracy of the positioning of the mold cylinder, which is the key to the safe operation of the instrument and smooth demolding. Due to the different sizes and structures of various compaction instruments, this machine has different positioning methods for mold testing and is equipped with corresponding accessories, making it easy and reliable to use. When demolding, the height of the tray should be adjusted first to meet different test molds. Place the test mold with the test block on the tray, paying attention to accurate positioning. When the test piece is removed, the power or oil supply valve should be turned off in a timely manner to stop the piston from rising, and the manual valve should be adjusted to lower the oil cylinder to the drunk point. When it reaches a certain height, the manual valve should be closed.

Electric hydraulic demoulder manufacturer*Notes:

1. It is strictly prohibited to not refuel and let the oil pump run idle.

2. Before use, the system must be completely emptied of air.

3. When using, the pressure reading should be observed, and it is strictly prohibited to exceed 35Mpa. When approaching

The power should be quickly cut off.

4. When demolding, attention should be paid to the rising distance of the oil cylinder, and it is strictly prohibited for the piston to come into contact with the test mold

To prevent damage to the components, operators should pay special attention.

5. After completing the experiment, the piston should be lowered to the bottom to prevent rusting caused by moisture on the piston.

YT-30 typeElectric hydraulic demoulder manufacturer*It mainly consists of accessories such as beams, columns, trays, shells, and bases. The crossbeam can be equipped with demolding and component accessories for various trial mold demolding purposes. The center hole of the oil cylinder plunger can be equipped with various accessories for easy demolding and component installation. The tray is used for positioning and supporting the mold barrel during demolding.Main specifications and technical parameters:

1. Drunk heavy load: 300KN

2. Range of force gauge: 0-60Mpa

3. Rising speed: 50c m/min

4. Oil drunk high working pressure: 30Mpa

5. Piston diameter 100 mm

6. Piston drunk large stroke: 280mm

7. Voltage: 380V/50HZ Power: 1100W Rotation speed: 1400 revolutions per minute

8. Dimensions: 600 × 520 × 1260mm (length × width × height)

9. Net weight: 120kg

Geotechnical testing instruments: 1006 mud viscosity meter, NB-1 mud specific gravity meter, NA-1 mud sand content measuring instrument, TM-85 soil density meter A, TM-85 soil density meter B, TDJ-III CNC multifunctional electric compaction instrument, YT-3 hydraulic demoulder, DTM-II electric demoulder, FG-III photoelectric liquid plastic limit measuring instrument, LP-100 digital liquid plastic limit measuring instrument, TYS-3 computer digital liquid plastic limit measuring instrument, light penetration meter, heavy penetration meter, manual demoulder, reaction frame, K30 flat load meter, free expansion rate measuring instrument, siphon tube, sand filling method bulk density measuring instrument, sub Jia Blue test mixing device, soil relative density meter, quick moisture content analyzer HKC-30, quick moisture content analyzer HKC-200, TS-4 soil moisture content analyzer, roadbed rebound modulus analyzer, YYW-1 lime soil unconfined pressure gauge, YYW-2 lime soil unconfined pressure gauge, standard penetrometer (63.5Kg), soil permeameter TST-70 type, soil permeameter TST-55 type, soil expansion meter WZ-2 type, soil shrinkage meter SS-1 type, sand filling tube # 100 type, sand filling tube # 150 type, sand filling tube # 200 type, alumina box 40X25, alumina box 55X35, alumina box 70X38, ring knife # 100 type, triangular scraper, triple low-pressure consolidation meter WG-1C type, triple medium pressure consolidation meter WG-1B type, triple high-pressure consolidation meter GDG-4 type, lightweight type WG-4 consolidation instrument, TSZ-2.0 three-axis instrument (medium pressure desktop), ZJ-1 equal strain direct shear instrument, DSJ-3 quadruple equal strain direct shear instrument, ZQWB-4 lightweight direct shear instrument, ZSZ-1 cross plate shear instrument (in-situ shear instrument), WYC-3 electric hydraulic forming demolding machine, ZY-2 vibration compaction molding machine, BZYS-4212 surface vibration compactor, DS-1 butterfly liquid limit tester electric, butterfly extensometer DY-2 (30-120mm), CLD-2/3 static cone penetration tester, natural consistency meter CD-1, natural slope meter QR-1