DSP-VF1400 High Temperature Atmosphere Box Furnace DSP-VF1400

mechanical properties

DSP-VF1400 High Temperature Atmosphere Box Furnace
Brief introduction
The DSP-VF1400 high-temperature vacuum box type atmosphere furnace uses silicon carbon rods as heating elements, adopts a three-layer shell structure and a Japanese Shimada 40 segment program temperature control system, with phase-shift triggering and thyristor control. The furnace is made of Japanese imported alumina polycrystalline fiber material, and the inner and outer chambers are equipped with an air cooling system, which can quickly raise and lower the temperature. The shell is sealed as a whole, and the cover plate and furnace door are sealed with high-temperature silicone O-rings. The furnace door is equipped with a water cooling system, and the gas enters from the rear chamber after passing through the flowmeter. After passing through the furnace, it is discharged through the outlet valve at the furnace door. This furnace can be sintered under vacuum. It has a KF25 quick connect interface on the side, which can be connected to a vacuum pump. The exhaust port of the vacuum pump is equipped with a smoke filter, and the exhaust port is equipped with a dust filter; And equipped with corrugated tubes, vacuum pumps (metal tubes connecting the furnace and vacuum), KF25 quick clamps, vacuum baffle valves, imported resistance vacuum gauges, etc. The furnace has a small vacuum degree of less than 5Pa and can also be supplied with protective gases such as hydrogen, argon, nitrogen, oxygen, carbon monoxide, ammonia decomposition gas, etc. The furnace has the advantages of small volume, balanced temperature field, low surface temperature, fast temperature rise and fall rate, energy saving, etc. It is an ideal product for atmosphere protection sintering and atmosphere reduction in universities, research institutes, and industrial and mining enterprises.
2、 Technical features
1. The sealing of this furnace adopts glove box technology, which has a very good sealing effect and can be used under vacuum or atmosphere. When vacuuming and maintaining pressure, it can ensure that the pressure gauge pointer does not deflect within 5 hours,
2. Software control system: The furnace is controlled by P93 instruments, each with a heating zone, and is equipped with communication interfaces and software. Various parameters of the furnace can be directly controlled through a computer, and the temperature display of the furnace and the operation of the instruments can be observed from the computer. The actual heating curve of the furnace will be drawn in real time by the computer, and the data can be saved and retrieved at any time.
3. Open lid protection system: The furnace is equipped with a travel switch, which automatically cuts off the power when the furnace lid is opened, effectively ensuring the safety of the user.
4. Sealing system: The top cover and door of the furnace (welded elsewhere) are both sealed with silicone O-rings, which are easy to remove, can be removed repeatedly, have good air tightness, and can ensure that the pressure gauge pointer does not deflect for 8 hours.
5. Vacuum system: It can pre evacuate the atmosphere box furnace to accelerate the cleaning of the air inside the furnace.
6. Furnace material: Imported from Japan, it does not shed powder, has good insulation performance, high reflectivity, balanced temperature field, and strong resistance to thermal expansion and contraction.
7. Heating element: All use Dia14mm heating rods, with low surface load and long service life.
8. Leakage protection function: The furnace is equipped with a leakage air switch, which automatically cuts off power when the furnace body leaks electricity to ensure safety during use.
9. Gas supply system: The furnace is equipped with a float flowmeter, and customers can control the gas flow rate through the float flowmeter or proton flowmeter.
10. Vacuum pump: VRD-16 vacuum pump is used.
11. (Optional) Explosion proof system: The explosion-proof system consists of solenoid valves, microcomputers, pressure displays and transmitters, 24V power supplies, AC contactors, etc. The pressure inside the furnace is converted into an electrical signal through pressure display and transmitter, and transmitted to the microcomputer. The microcomputer compares it with the set value and then gives a signal to control the AC contactor, thereby controlling the on/off of the solenoid valve. When the pressure inside the furnace exceeds the allowable pressure we set, the solenoid valve immediately opens, playing an explosion-proof role. We have installed an exhaust pipe on the solenoid valve, and users can connect the pipe to discharge the gas outdoors
3、 This explosion-proof system has many advantages:
(1) Reusable: When the pressure is greater than the set value, the solenoid valve opens, and when the pressure is lower than the set value, the solenoid valve closes. Unlike mechanical * *, it cannot be used after one explosion.
(2) Adjustable setting value: Users can adjust the opening pressure of the solenoid valve according to their needs through a microcomputer
(3) The explosion-proof point is very sensitive: due to the use of microcomputers and electrical signals, it will explode immediately when the pressure reaches the explosion-proof point
(4) Explosion proof system safety: No fragments fly out during detonation. (If a mechanical one is used, glass sheets may fly out)
(5) The explosion-proof system has good stability: due to the use of microcomputers and solenoid valves, it will definitely explode at our set point, and users can test it. Unlike mechanical testing, which cannot be tested, there is also a lot of uncertainty about whether it will open at the explosion-proof point.
4、 Technical parameters
1. Model: DSP-VF1400 High Temperature Vacuum Box Atmosphere Furnace
2. Power: 8KW
3. Furnace size (mm): 300X200X200
External dimensions（mm）：600X610X 1440
4. Power supply: Voltage 220V
5. Number of phases: single-phase
6. Heating element: silicon carbide rod
7. Control method
FP93 temperature control instrument (Shimadzu, Japan)
A、 The 40 segment temperature control program can be divided into 4, 2, and 1 groups of programs. If divided into 4 groups of programs, each program has 10 segments,
B、 Six sets of PID control can be used for low, medium, and high temperatures, so that each temperature range can be controlled accurately.
C、 Equipped with over temperature protection and thermocouple breaking protection, the heating circuit of the electric furnace will automatically cut off in case of over temperature or thermocouple breaking (when the temperature of the electric furnace exceeds 1420 degrees or the thermocouple burns out, the AC relay on the main circuit will automatically disconnect, the main circuit will be disconnected, the ON light on the panel will turn off, and the OFF light will turn on, providing limited protection for the electric furnace).
D、 The instrument is available in Fahrenheit (F) and Celsius (C) for selection
E、 Equipped with 485 communication interface (standard when selecting software)
F、 Equipped with automatic shutdown function
G、 It can store multiple sets of programs and can be accessed freely when in use.
H、 It has a power-off protection function, which means that when the furnace is powered on after a power outage, the program does not start rising from the starting temperature, but from the furnace temperature when the power is cut off.
I、 The instrument displays the output power, number of program execution segments and execution time, and whether the program is in a heating, constant temperature, or cooling state.
J、 The instrument has a skip step function (i.e. the instrument can skip one step and directly execute the next step).
K、 The instrument has the function of temperature self-tuning.
8. Furnace material:1600Imported alumina polycrystalline fiber from Japan
9. Control accuracy:+/- 1 ℃
10. Trigger: Phase shift trigger
11. Electrical appliances: Zhejiang Chint
12. Controllable silicon: 106/16E Siemens AG, Germany
13. High temperature: 1400 ℃
14. Rated temperature: 1350 ℃
15. Vacuum * high temperature 1200 ℃
16. Vacuum degree ≤ 10Pa in cold state
17. Heating rate: ≤ 20 ℃/Min (can be modified according to requirements)
18. Recommended heating rate: ≤ 10 ℃/ Min
19. Thermocouple model: S-type
20. Surface temperature around ≤ 45 ℃

High operating temperature of VF1400 under various atmospheres and vacuum conditions