The constant temperature incubator has been improved and manufactured according to market demand
constant temperature incubatorIt has a temperature and humidity control system that provides various environmental simulation conditions required for industrial research and biotechnology testing. Therefore, it can be widely applied to sterile testing, stability inspection, as well as testing of raw material properties, product packaging, product life, etc. in pharmaceuticals, textiles, food processing, and industrial products.
The constant temperature incubator has parameter memory protection for data loss caused by power outages and crashes, as well as call recovery function. It adopts a domestic streamline arc design, and the shell is made of cold-rolled steel plate with surface electrostatic spraying. The working chamber is made of mirror stainless steel material; The temperature control system adopts microcomputer microcontroller technology, with high temperature control accuracy; Equipped with temperature, humidity, and time adjustment control, as well as touch sensitive keyboard settings for adjustment; It is displayed as a dual screen high brightness digital tube display, with accurate and intuitive readings and * performance.
The constant temperature incubator has timing and timing functions; The studio is equipped with lighting fixtures and large angle insulated vacuum tempered glass for easy observation;constant temperature and humidity chamberThe standard configuration is lighting, and the height and number of shelves in the studio can be adjusted according to user requirements; The humidity sensor adopts imported components, the humidification component adopts intelligent atomizer, and the large capacity humidification water tank. During transportation of the constant temperature incubator, be careful not to apply force on the glass or collide with the box. Do not invert or tilt at an angle greater than 45 degrees.
After the constant temperature incubator is placed on the ground, it should be placed steadily. If the ground is uneven, it should be corrected. Please do not use the instrument in places with direct sunlight or high temperature and humidity. Keep the ambient temperature between 10-30 ℃. The constant temperature incubator should be kept away from electromagnetic interference sources and the grounding wire of the equipment should be effectively grounded. During normal operation, the placement of the contents inside the incubator should not affect air circulation to ensure air circulation and uniform temperature inside the incubator. The power supply of the constant temperature incubator is AC 220V 50HZ, and a 10A three core socket must be used with a reliable grounding wire. Two core sockets are not allowed to be used without authorization. The power cord should not be placed close to the back, and instruments or other objects should not be pressed on the power cord to avoid damaging it
The constant temperature incubator should be installed in a place with minimal temperature and humidity changes, using a three pin plug. The socket should be properly grounded. Before starting, it is necessary to fully familiarize and understand the instructions of each component and supporting instrument, and master the correct usage method. It is strictly prohibited to place volatile chemical solvents, explosive gases, and flammable gases inside the box,constant temperature and humidity chamberFlammable sprays shall not be used nearby to avoid electric spark ignition. Check the gas circuit frequently for air leakage.
The constant temperature incubator has a power-off protection function, so it takes about a minute and a half to restart the compressor after it stops, in order to better protect the compressor. The distance between the condenser and the wall should be greater than 100mm, and there should be a 50mm gap on the side of the box. The top of the box should have at least 300mm of space to ensure good heat dissipation. When handling, repairing, and maintaining a constant temperature incubator, collision, shaking, and vibration should be avoided. The maximum inclination should be less than 45 degrees. When not in use for a long time, the main power and the power switch at the back of the equipment should be turned off. During the operation of the incubator, frequent door opening should be avoided to maintain temperature stability and prevent dust and dirt from entering the working chamber.
The inside and outside of the constant temperature incubator should be kept clean daily, and should be cleaned after each use. Even if not in use for a long time, it is necessary to regularly wipe the inner walls and equipment surfaces to maintain cleanliness and increase the transparency of the glass. Do not use acid, alkali, or other corrosive solutions to wipe the outer surface. After the cultivation is completed, turn off the power switch. If the experimental sample is not taken out immediately, do not open the box door.constant temperature incubatorNot suitable for use in abnormal environments such as high voltage, high current, and strong magnetic fields. Strictly follow the electrical safety operation rules.